manualshive.com logo in svg

Sanyo MDF-393, Service Manual, Page: 27 / 34

Share
Download
Sanyo MDF-393 Service Manual Download Page 27

15.  Lamp, display and buzzer specifications

Lamp operation:

 <Control 

PCB> 

DP1: 

DP2: 

DP3: 

DP6: 

<Display PCB> 

DP51: 

DP53: 

DP54: 

DP55: 

Examples of display:

Orange 

lamp

Goes off: High/low temp. alarm (15min. delay), sensor error,

power failure 

Lit 

: Not in alarm condition 

Green 

lamp 

Goes off: L side compressor turns off. (normal condition) 
Lit 

: L side compressor turns on. 

Red 

lamp 

Goes off: Capillary heater turns off. (normal condition) 
Lit 

: Capillary heater turns on. 

Green 

lamp 

Goes off: H side compressor turns off. (normal condition) 
Lit 

: H side compressor turns on. 

Red 

lamp

Blinks  : High/low temp. alarm (without delay), or sensor failure,

or power failure 

Orange 

lamp 

Lit 

: In filter alarm 

Red 

lamp 

Lit 

: Door ajar 

Orange 

lamp 

Lit 

: Battery accumulation time is reached to about 3 years 

Blinks  : Fan motor accumulation time is reached to about 6 years 

Decimal point of chamber temp. -80.0

Chamber temp.  -79.5

㷄

 

Set temp.  

-80.0

㷄

 Sensor 

offset

㩷 㩷 㩷

          -5.0  

Operation monitoring

㩷 㩷

LCP

Function

㩷 㩷 㩷

          F03  

Error 

㩷 㩷 㩷 㩷

                E01  

Service code

㩷 㩷 㩷

 384 

Set value

㩷 㩷 㩷

 004 

Accumulation time

㩷 㩷

8H timer 135 

Key Lock

㩷 㩷 㩷

 L_0 

 Buzzer 

tone:

 Alarms 

Key operation 

Set value memory 
Out of settable range 
Filter blockage 

Intermittent 

tone 

Click tone 
Click tone 
1 second continuous tone 
Intermittent tone 

24

 

Summary of Contents for MDF-393



































Reviews:

No comments