background image

8. 

Function mode 

F01 

Setting of High temp. alarm set temperature

F02 

Setting of Low temp. alarm set temperature

F03 

Display of battery accumulation time

F05 

Setting of compressor delay time

F06 

Service code input (code: 384)

F07 * 

Temp. sensor Zero Adjustment

F08 * 

Cascade sensor Zero Adjustment

F09 

Factory test mode …… Unavailable

F10 

Factory test mode …… Unavailable

F11 

Factory test mode …… Unavailable

F12 * 

Display of temperature in temp. sensor

F13 * 

Display of temperature in cascade sensor

F14 * 

Display of temperature in compressor sensor

F15 * 

Display of temperature in AT sensor

F17 * 

Model code setting (Initialization of non-volatile ROM and memory)

F18 * 

Capillary heater is forcibly turned on/off

F19 

Factory test mode …… Unavailable

F20 

Factory test mode ... ... Unavailable

F21 

Communication ID set ... ... Unavailable

F22 

Communication mode set ... ... Unavailable

F23 * 

Display of power supply voltage

F24 

Remote alarm terminal output

F25 

Alarm resume time set

F26 * 

Display of actual operation rate

F27 * 

Display of diagnosis value for running rate ... ... Unavailable

F28 * 

Factory test mode …… Unavailable

F29 * 

Factory test mode …… Unavailable

F30 * 

ROM version is displayed

F31 * 

Selectable buzzer ON/OFF setting in filter alarm

F32 * 

Display of condensing fan motor accumulating time

 Setting  

In chamber temperature display, keep pressing 

key over 5seconds to 

procedure:  

display “F00”. 
Input the desired function code with  

key and  

key. 

Press SET key to be function mode available. 
* … You should input service code in F06 beforehand. 
To cancel service code, input “000” in F06 or turn the power off. 

F01: 

<Purpose>  To set high temp. alarm set temperature 

<Operation>  Input F01 and press SET key to display “010” (initial value). 

Set the value in the range “005”~“020” with

 key and

  key. 

Press SET key to store the value and revert to chamber temperature 
display. 

F02: 

<Purpose>  To set low temp. alarm set temperature 

<Operation>  Input F02 and press SET key to display “-10” (initial value). 

Set the value in the range “-05”~“-20” with  

key and 

key. 

Press SET key to store the value and revert to chamber temperature 
display. 

F03: 

<Purpose>  Battery accumulation time is displayed 

<Operation>  Input F03 and press SET key to display alternately F03 with “00.0” 

(in case battery used for a month or less). Press SET key to revert to 
chamber temperature display. 

<Reset>  

Input 

409

’ and press SET key to initialize battery accumulation time. 

(’00.0’ is displayed) 

18

 

Summary of Contents for MDF-393



































Reviews: