Sanyo HV-DX350A, Instruction Manual

Page: 21 / 66

18 19
Initial Installation
18 19
Initial Installation
Basic
O
peration
Setting up the player
■
Switch the TV on.
■
You can also start "AUTO SEARCH" in the SETUP "PR PRESET"
➝
"AUTO SEARCH".
■
To tune in new stations (manual tuning) and to enter station names see page 27-28.
LANGUAGE SET
ENGLISH
DEUTSCH
ITALIANO
ESPAÑOL
FRANÇAIS
NEDERLANDS
PR+/-:SELECT
OK:CONFIRM SETUP:END
SETUP:END
PLEASE WAIT...
CH 25
You should see this picture the first time you switch on the TV and
player.
Choose your language.
2
Press on the remote control and RF36 will be displayed on the
front of your player.
Select a free channel on your TV and manual tune the channel
until the blue screen as shown in step 2 appears. Refer to the TV
manual for more details.
1
Then choose your country.
3
OK for "AUTO SEARCH!".
"AUTO SEARCH" tunes in all the stations you can receive in your
country.
4
• If you don't see the menu picture below after you press the menu button it may be because you don't
use a RCA cable and you need to tune the television to the player (see 'Connecting your player through
RF lead' on page 12). Normally a new player outputs a signal via the RF lead on transmission channel 36.
Search for the menu picture with the channel tuning function of your TV set (see its user manual). Some
televisions allow you to key in the transmission channel number in their tuning set-up menu.
• In case there will be interference problems with other transmission channels when the player outputs a
signal on transmission channel 36, the AUTO SEARCH process usually recommends an alternative, as in
step 4.
• There is a another way of setting RF output channel, if needed please see 'Connections and Assembling
on page 35'. It does not apply to models which do not generate the RF output signal.
CHECK IT!
COUNTRY SET
AUSTRALIA
NEW ZEALAND
PR+/-:SELECT
OK:CONFIRM SETUP:END
Press the [OK] button to confirm the recommended RF channel.
Should you wish the stations to have the same numbers as those
used on the TV, follow the instructions in "Sorting programme
locations" on page 28.
Else ...
exit the basic installation function and enjoy your player.
7
Should you wish the stations to have the same numbers as those
used on the TV, follow the instructions in "Sorting programme
locations" on page 28.
Else ...
Press the SETUP button to exit the set-up menu and enjoy your
player
8
If other stations are positioned on near the current RF OUTPUT CH,
the guide message appears automatically.
The player recommends the optimal RF OUTPUT CH number
automatically.
6
If the clock has not been set, the clock setting screen will appear.
Please see “Setting time and date” on page 20.
5
• If the signal from the player is coming into the TV through
the RF lead, the picture will disappear when you press OK at
step 8. You will need to re-tune your television to the new
UHF transmission channel.
Up [PR+], down [PR-], OK and 'confirm'
• Notice the on-screen prompts which the video recorder generates to tell you which button to press.
In general the up and down 'navigation' buttons select or highlight something and the OK button
confirms it .
• [PR+] and [PR-] are the same buttons as 'up' and 'down'.
• In the DVD section it is usually the left and right buttons which 'select'.
CLOCK SET
0-9:SETUP (HOUR)
/
➝
:CORRECT SETUP:END
TIME - - : - -
DATE - - / - - /- - - -
➝
PLEASE CHANGE THE TV
CH TO 34.
IMPORTANT!
RF OUTPUT SET
0-9:SELECT(21-69)
OK:CONFIRM SETUP:END
CURRENT CH 36
RECOMMENDED CH 34
MANUAL SET
PR01 P-01 PR08 P-08
PR02 P-02 PR09 P-09
PR03 P-03 PR10 P-10
PR04 P-04 PR11 P-11
PR05 P-05 PR12 ----
PR06 P-06 PR13 ----
PR07 P-07 PR14 ----
PR+/-:SELECT
OK:CONFIRM SETUP:END