![background image](http://html.mh-extra.com/html/sanyo/dvp-p1/dvp-p1_technical-information_362046018.webp)
–18–
3-10. “CHASSIS,SUB LOWER
(7E000) ”
(See Fig. 3-10-1)
1)
Referring to section 3-7, remove the “ASSY, LEVER,
PULLEY
(4G100)
” and the “PULLEY, RELAY DRUM
(4G200)
”.
2)
Remove the two “SCR S-TPG BIN 2.6X4
(7F000)
” and
remove the “CHASSIS,SUB LOWER
(7E000)
”.
ASSEMBLY NOTES:
1.
Install the “CHASSIS,SUB LOWER
(7E000)
” so that
portions A and B hook onto the “ASSY,CHASSIS R
(7A000)
” and the “ASSY,CHASSIS L
(7C000)
” respec-
tively as shown in Fig. A and Fig. B.
2.
Install the “CHASSIS,SUB LOWER
(7E000)
” so that it
does not contact the relay gear on the “COMPL,MOTOR
CAM
(6A000)
”.
CHASSIS,SUB LOWER
(7E000)
SCR S-TPG BIN
2.6X4
(7F000)
SCR S-TPG BIN
2.6X4
(7F000)
Relay Gear on the
COMPL,MOTOR CAM
(6A000)
Fig. B
Fig. A
Portion B
Hook
Hook
Portion A
Fig. 3-10-1
3-11. “COMPL,HOLDER,PINCH SIDE
(5A000) ”, “COMPL,HOLDER,PINCH
PICK
(5D000) ”, “COMPL,HOLDER,
PINCH EXIT F
(5E000) ”, and “COMPL,
HOLDER,PINCH EXIT
(5B000) ”
(See Figs. 3-11-1 to 3-11-3)
NOTE: Be careful not to dirty the pinch rollers on each
“COMPL,HOLDER,PINCH
”.
1)
Referring to section 3-3, remove the “ASSY,LEVER,TPH
DOWN
(1F000)
” and the “COMPL,HOLDER TPH
(1A000)
”.
2)
Referring to section 3-5, remove the “ASSY,
ROLLER,PICK GEAR
(6J000)
” and the “ARM,TRAY
PAPER L
(6L000)
”.
3)
Referring to section 3-6, remove the “ASSY, MOTOR
STEPPING
(4K000)
”.
4)
Referring to section 3-8, remove the “PULLEY,DRUM
(4F000)
”.
5)
Referring to section 3-9, remove the “COMPL,MOTOR
CAM
(6A000)
” and the “ASSY,GEAR,CAM
(5J000)
”.
6)
Referring to section 3-10, remove the “CHASSIS,SUB
LOWER
(7E000)
”.
7)
Remove the “SPRING,PINCH ROLLER F
(5F000)
” on
the both sides. (Refer to Fig. 3-11-1 and Fig. 3-11-2.)
8)
Remove the “COMPL,HOLDER,PINCH SIDE
(5A000)
”.
(Refer to Fig. 3-11-2.)
9)
Remove the “SPRING,PINCH ROLLER RB
(5H000)
” and
the “SPRING, PINCH ROLLER LB
(5G000)
”. (Refer to
Fig. 3-11-1 and Fig. 3-11-3.)
10) Remove the “COMPL,HOLDER,PINCH PICK
(5D000)
”.
(Refer to Fig. 3-11-2.)
11) Remove the “COMPL,HOLDER,PINCH EXIT F
(5E000)
”.
(Refer to Fig. 3-11-3.)
12) Remove the two “SPECIAL WASHER-1.5X0.5
(5C000)
”
on the both sides and the “COMPL,HOLDER,PINCH
EXIT
(5B000)
”. (Refer to Fig. 3-11-3.)
ASSEMBLY NOTES:
1.
Install the “COMPL,HOLDER,PINCH EXIT
(5B000)
” so
that the left and the right (the black part and the white part)
of it are in proper position. (Refer to Fig. 3-11-3.)
2.
Install the “COMPL,HOLDER,PINCH EXIT F
(5E000)
” so
that the left and the right (the black part and the white part)
of it are in proper position. Insert shafts of the both side
into the each big holes, then move them to the each small
holes as shown in Fig. F of Fig. 3-11-3.
3.
Install the “COMPL,HOLDER,PINCH PICK
(5D000)
” so
that the left and the right (the black part and the white part)
of it is in proper position. Insert shafts on both sides into
each big hole, then move them to each small hole as
shown in Fig. C of Fig. 3-11-2.
4.
Install the “SPRING,PINCH ROLLER LB
(5G000)
” as
shown in Fig. E of Fig. 3-11-2.
5.
Install the “SPRING,PINCH ROLLER RB
(5H000)
” as
shown in Fig. A of Fig. 3-11-2.
6.
Apply grease (VJ8-0229) to points where the shafts of the
“COMPL,HOLDER,PINCH EXIT
(5B000)
” contact the
“SPRING,PINCH ROLLER RB
(5H000)
” and “SPRING,
PINCH ROLLER LB
(5G000)
”. (Refer to Fig. 3-11-1 and
Fig. 3-11-3.)
7.
Insert shafts of both sides of the “COMPL,HOLDER,
PINCH SIDE
(5A000)
” into each big hole, then move
them to each small hole as shown in Fig. C of Fig. 3-11-1.
8.
Install the “SPRING,PINCH ROLLER F
(5F000)
” as
shown in Fig. B of Fig. 3-11-1 and Fig. D of Fig. 3-11-2.
9.
Referring to section 3-14, be careful not to allow dust or
the trash to stick to the surface of the “COMPL,PIPE
DRUM RUBBER
(4A000)
”.