manualshive.com logo in svg

Sanyo Colour CCD Camera VCC-5775P, Instruction Manual

Share
Download
Sanyo Colour CCD Camera VCC-5775P Instruction Manual Download Page 8

MOUNTING THE LENS

Please use a DC type auto-iris lens (sold separately).

Checking the lens mount

Do not use lense with a length 

L

 more than 

5

 mm. If not, that may

damage the camera and prevent proper installation.

1

Remove the lens mount cap from the camera.

2

Install the auto-iris lens.
CS mount type lens

Carefully align the lens mount with the camera opening, then turn the lens
slowly to install it.

C mount type lens

Install the supplied C-mount adaptor on the lens mount, then carefully
align the lens mount with the camera opening and turn the lens slowly to
install it.

3

Connect the lens plug to the lens iris output connector (LENS) on
the side of the camera.

The plug shape may not correspond to the terminal on the camera. In such
a case, remove the original plug and using a soldering iron, connect the
supplied 

lens iris plug

 according to the diagram. (Refer to page 

8

.)

L

1

C mount
type lens

2 

3

2

CS mount
type lens

L53V2/XE (VCC-5775P)  GB  2000, 7, 11

English

 7

Summary of Contents for Colour CCD Camera VCC-5775P





















Reviews:

No comments

Brands by name

Popular brands

Load more brands