manualshive.com logo in svg

Sanwa PC720M, Instruction Manual

Share
Download
Sanwa PC720M Instruction Manual Download Page 52

― 49 ―

5-9-2 Diode (

 ) test

1) 

What to measure

 

(Diode test): Judging the diode (Good or defective)

2) 

 Measuring procedure

①

Connect the red plug of the test lead to 

  measuring 

terminal and the black one to the COM terminal.

②

Set the function selector to 

, then press the SELECT 

button to select the diode test. 
 (The sub display shows [diod].)

③

Apply the black test pin to the cathode of the diode, and the 

red one to the anode.

④

The display will show the forward voltage drop (forward 

biased).

*

Forward biased voltage drop for a good silicon diode is 

between 0.400V to 0.900V. A reading higher than that 
indicates a defective diode. A zero (or close to)reading 
indicates a defective diode (shorted). An OL indicates a 
defective diode (open).

⑤

Apply the red test pin to the cathode of the diode, and the 

black one to the anode.

*

A reading [OL] for reverse biased voltage drop indicates 

the diode is good. Any other readings indicate the diode is 
defective  (resistive or shorted).

Summary of Contents for PC720M

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands