Santak CASTLE On-Line Series User Manual Download Page 8

 

- 1 - 

 

1.  Introduction   

 

  The  Castle  On-Line-Series  is  an  uninterruptible  power  supply 

incorporating  double-converter  technology.  It  provides  perfect  protection 
specifically for Computer equipment, communication systems and industry 
control systems.   

The  double-converter  principle  eliminates  all  mains  power 

disturbances.  A rectifier converts the alternating current from the socket 
outlet  to  direct  current.  This  direct  current  charges  the  batteries  and 
powers the inverter. On the basis of this DC voltage, the inverter generates 
a pure sinusoidal AC voltage, which permanently supplies the loads.   

Computers  and  periphery  are  thus  powered  entirely  by  the  mains 

voltage.  In  the  event  of  power  failure,  the  maintenance-free  batteries 
power the inverter. In the event of inverter failure/Overload, UPS transfer 
to bypass mode, after the failure/overload remove, UPS transfer to inverter 
mode continue supplies the loads.   

This  manual  covers  the  UPS  listed  as  follows.  Please  confirm 

whether  it  is  the  model  you  intend  to  purchase  by  performing  a  visual 
inspection of the Model No. on the rear panel of the UPS.   

 

3C15KS:

 Three phase input single phase output, can used with external 

EBM to get longer backup time. 

3C20KS:

 Three phase input single phase output, can used with external 

EBM to get longer backup time. 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for CASTLE On-Line Series







































Reviews: