background image

IMPORTANT PLEASE READ 

All  products  manufactured  and  supplied  by 

B

AGNODESIGN  are  fit  for  purpose  as  long  as 

they  are  Installed,  used  correctly,  cleaned  and  receive  regular  maintenance  in  accordance 
with  these instructions ... 

Remove all packaging and check the product for damage or missing parts before commencing with 
the installation. 

Any alterations made to this product and its components may infringe product certification, infringe 
water  regulations and invalidate the  guarantee. The Installation  must  comply  with  all  local/national 
water  supply  authority  regulations/bylaws  and  building  and  plumbing  regulations,  therefore  we 
strongly recommend that your product be installed by a reputable qualified trade's person. 

PRODUCT LIFECYCLE 

"The product LiveCycle/e is the collective stages that a product goes through from 

its 

conception 

and design through to its ultimate disposal." 

DISPOSAL GUIDANCE 

The best way to ensure your Product has a long life is to follow the Care and Maintenance guides set 
by the Manufacture after purchase. This document can be found at 

www.sanipexgroup.com. 

The  life  cycle  of  the  product  is 

not 

in correlation  to  the  product  Guarantee;  the  standards 

the products  are  manufactured  or  certified  to  (e.g.  CE  &  WRAS)  can  exceed  past  the 
Guarantee duration. After the life cycle of the product  is deemed complete by the end-user 
please follow the below to dispose of the items correctly ... 

Mixers (Taps): 

If the mixers are no longer accepted due to mechanical use or aesthetic style, these can be disposed 
of  at a  registered Local  Authority waste recycling center where the individual components can be 
sorted. 

CLEANING CARE GUIDE 

Only use a mild soap and water for cleaning. 
Rinse with water to remove the mild soap solution. 

We recommend the product is dried using a soft cloth after 
every use. 

Never 

use any abrasive or strong cleaning products containing, 

bleaches, acids (hydrochloric, formic, phosphorus, chlorine or 

acetic),  strong detergents, limescale remover, alcohol or dyes etc. 

Never 

use abrasive cleaning pads, wire wool or microfibre cloths. 

Never 

use cleaning equipment that may have been pre-used and 

contaminated with the above substances. 

Never 

apply the cleaning product directly onto the finished 

surface. 

�� 

�� 

�� 

Summary of Contents for BAGNO DESIGN BDM-BIS-451L Series









Reviews: