manualshive.com logo in svg

SANDVIK MT520/PLC, Technical Description

Share
Download
SANDVIK MT520/PLC Technical Description Download Page 23

SANDVIK Tunneling Miner 

MT520 / 

PLC

 

 

Page 23 of 31 

 

 

www.sandvik.com

 

 

 

 

Technical description-MT520-PLC specification .220.Rev 1

 

 

The APC (

A

utomation 

P

ersonal 

C

omputer) which is used for the Profile Control and Monitoring System. 

The visualization software runs under 

MS WINDOWS XP

®

. 

The 15” flat screen monitor is mounted ergonomically inside the driver’s cabin, in good visibility for the 
operator. 

 

 

 

 

 

 

 

 

The different screen levels provide the following information: 

 

•

 

The pre-programmed profile (green line) in relation to the maximum cuttable profile (blue line). 

•

 

The actual position of the cutter boom including measurements to the boundaries. 

•

 

The cutter head is colored green as long as it is cutting inside the pre-programmed profile and 
colored red if outside. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Automation panel 

APC 

Summary of Contents for MT520/PLC
































Reviews:

No comments

Brands by name

Popular brands

Load more brands