S&T TPMS1209T02-ER User Manual Download Page 17 | Manualshive

Page: 17 / 28

S&T TPMS1209T02-ER User Manual Download Page 17

Page 17 of 28

Function: the system will issue the high pressure alarm when the tire

pressure is 25% higher than the standard.

Alarm mode: the alarm lamp flashes, high pressure warning iron, tire

position icon and the audible alarm turn on together.

Treatment: press any key to stop the audible alarm. The red alarm lamp

remains on and the display reverts to the normal mode. At

this time user should adjust the tire pressure to the normal

level with the reasonable method. The red alarm lamp goes

off only when the tire pressure returns to the normal level.

3. Low pressure level 1 alarm

Display mode:

Function: the system will issue level 1 low pressure alarm when the tire

pressure is 12.5% lower than the standard.

Alarm mode: the alarm lamp flashes, low pressure level 1 alarm iron, tire

position icon and the audible alarm turn on together.

Treatment: press any key to stop the audible alarm. The red alarm lamp

remains on and the display reverts to the normal mode. At

this time the user should adjust the tire pressure to normal

level as soon as possible. The red alarm lamp goes off only

«
...
15
16
17
18
19
...
»

Summary of Contents for TPMS1209T02-ER





























Reviews:

No comments