manualshive.com logo in svg

Sandpiper S20, Operating Manual

Share
Download
Sandpiper S20 Operating Manual Download Page 24

s20mdl1sm-REV0708 

Model S20 Metallic Page 22

PILOT VALVE SERVICING 

To service the pilot valve fi rst shut 

off the compressed air supply, bleed 
the pressure from the pump, and 
disconnect the air supply line from the 
pump.

 

STEP #1:

 See pump assembly 

drawing.

Using a 1/2" wrench or socket, 

remove the four capscrews (item 11). 
Remove the air inlet cap (item 8) and 
air inlet gasket (item 21). The pilot valve 
assembly (item 4) can now be removed 
for inspection and service.

STEP #2:

 Disassembly of the pilot 

valve.

Remove the pilot valve spool (item 

4-D). Wipe clean and inspect  spool and 
o-rings for dirt, cuts or wear. Replace 
the o-rings and spool if necessary.

Remove the retaining ring (item 

4-F) from the end of the sleeve (item 
4-B) and remove the sleeve from the 
valve body (item 4-A). Wipe clean and 
inspect sleeve and o-rings for dirt, cuts 
or wear. Replace the o-rings and sleeve 
if necessary.

STEP #3:

 Re-assembly of the pilot 

valve.

Generously lubr icate outside 

diameter of the sleeve and o-rings. 
Then carefully insert sleeve into valve 
body. Take CAUTION when inserting 
sleeve, not to shear any o-rings. Install 
retaining ring to sleeve. Generously 
lubricate outside diameter of spool and 
o-rings. Then carefully insert spool into 
sleeve. Take CAUTION when inserting 
spool, not to shear any o-rings. Use 
BP-LS-EP-2 multipurpose grease, or 
equivalent. 

STEP #4:

 Re-install the pilot valve 

assembly into the intermediate.

Be careful to align the ends of the 

pilot valve stem between the plunger 
pins when inserting the pilot valve into 
the cavity of the intermediate.

Re-install the gasket, air inlet cap 

and capscrews. Connect the air supply 
to the pump. The pump is now ready 
for operation.

Pilot Valve Servicing, Assembly Drawing & Parts List

PILOT VALVE ASSEMBLY PARTS LIST

ITEM PART 

NUMBER  DESCRIPTION 

QTY

4 095-110-000  Pilot 

Valve 

Assembly 

1

4-A 095-095-157 

Valve 

Body 

1

4-B 

755-052-000 

Sleeve (With O-rings) 

1

4-C 560-033-360 

O-ring 

(Sleeve) 

6

4-D 

775-055-000 

Spool (With O-rings) 

1

4-E 560-023-360 

O-ring 

(Spool) 

3

4-F 675-037-080 

Retaining 

Ring 

1

FOR PUMPS WITH CAST IRON CENTER SECTION

ITEM PART 

NUMBER  DESCRIPTION 

QTY

4 095-110-558  Pilot 

Valve 

Assembly 

1

4-A 095-095-558 

Valve 

Body 

1

(includes all other items used on 095-110-000)

FOR PUMPS WITH STAINLESS STEEL CENTER SECTION

ITEM PART 

NUMBER  DESCRIPTION 

QTY

4 095-110-110  Pilot 

Valve 

Assembly 

1

4-A 095-095-110 

Valve 

Body 

1

(includes all other items used on 095-110-000)

Summary of Contents for S20
































Reviews:

No comments

Brands by name

Popular brands

Load more brands