manualshive.com logo in svg

Sandpiper S20, Operating Manual

Share
Download
Sandpiper S20 Operating Manual Download Page 14

s20mdl1sm-REV0708 

Model S20 Metallic Page 12

Composite Repair Parts Drawing

476-227-000 

AIR END KIT

 (Aluminum Center)

 

Seals, O-ring, Gaskets, Retaining Rings, Air Valve 

 

Sleeve and Spool Set and Pilot Valve Assembly.

476-170-000  

AIR END KIT

 (Air Valve with Stroke Indicator Pin, Aluminum Center)

 

Seals, O-ring, Gaskets, Retaining Rings, Air Valve 

 

Sleeve and Spool Set, and Pilot Valve Assembly.

476-042-360  

WET END KIT

 

Nitrile Diaphragms, Balls, and Seats.

476-042-656 

WET END KIT

 

Santoprene Diaphragms, Balls and EPDM Seats.

476-042-365  

WET END KIT

 

Neoprene Diaphragms, Balls and Seats.

476-042-633  

WET END KIT

 

FKM Diaphragms, PTFE Balls and FKM Seats.

476-042-635 

WET END KIT

 

Neoprene Diaphragms, PTFE Overlay, PTFE Balls 

 and 

PTFE 

Seats.

476-042-364 

WET END KIT

 

EPDM Diaphragms, Balls and Seats.

476-042-654 

WET END KIT

 

Santoprene Diaphragm, PTFE Overlays, PTFE Balls, PTFE Seats.

476-042-659 

  WETTED END KIT

  One-PIece Bonded PTFE/Nitrile Diaphragm, 
  PTFE Balls, PTFE Seats.

475-216-000 

MIDSECTION CONVERSION KIT

 

(Replaces Aluminum Midsection With Cast Iron 

 

Components) Air Inlet Cap, Intermediate Bracket, Inner 

 

Chamber and Inner Diaphragm Plates.

Hardware Kits

475-200-330 

Zinc Plated Capscrews, Washers, and Hex Nuts.

475-200-115 

Stainless Steel Capscrews, Washers, and Hex Nuts.

**

Electronic Leak Detector Kits

032-037-000 100-120/220-290 

VAC

032-045-000 12-32 

VDC

Available Service And Conversion Kits

Overlay 
Diaphragm Option

**Note: Pumps equipped with these components are not ATEX compliant

One-Piece Bonded
Diaphragm Option

Summary of Contents for S20
































Reviews:

No comments

Brands by name

Popular brands

Load more brands