Run 120V AC house wiring to the location of the fan. Use only UL-approved connectors (not included) to attach the house wiring to the
wiring plate. Refer to the wiring diagram, and connect the wires as shown.
CONNECT ELECTRICAL WIRING
Install ceiling material to complete the ceiling construction. Then, cut around the fan housing.
To attach the grille assembly to the fan housing, pinch the grille springs on the sides of the grille
assembly, and position the grille into the housing with the grille springs in the appropriate slots.
Push the grille assembly towards the ceiling to secure.
INSTALL GRILLE
SERVICE PARTS
PART
PART NAME
Qty.
1
2
3
4
5
6
7
8
9
10
11
12
a
d
e
f
b
c
Housing
Screw
Screw
Screw
Screw
Screw
Screw
Blower
Motor
1
2
1
Power box
1
1
1
1
1
1
1
1
1
3
3
3
1
1
1
Grille Assembly (includes part 2)
Grille Spring
Hanger Bar
Blower Assembly includes part 3, 4, 5, 6, b, c.
*Replacement parts are shown for illustration purposes only and are not sold seperately
WARNING:
Before replacing, be sure to turn off power at power source.
WARRANTY
1
2
3
4
a
b
f
e
d
8
9
10
11
12
6
7
c
5
Damper / Duct Connector
Wire Panel / Harness Assembly
Blower Wheel
Wiring plate
Motor plate
UNIT
BLACK (BLK)
SWITCH BOX
SWITCH
I
POWER SUPPLY
120V AC
GROUND (GRD)
WHITE (WHT)
FAN
RECEPTACLE
WIRE
PANEL
SWITCH
I
SWITCH
II
SWITCH
II
BROWN (BRN)
FAN
BRN
BLK
WHT
UNIT
SWITCH BOX
WHT
GRD
GRD
LINE
IN
BLK
S&P USA Ventilation Systems, LLC. & S&P Canada Ventilation Products, Inc. warrants to the original end user of its products that our exhaust fans will be free from defects in
materials and workmanship for a period of Six (6) years from the date of original purchase. THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING
BUT NOT LIMITED TO IMPLIED WARRANTIES OF SUITABILITY FOR A PARTICULAR PURPOSE.
During this six year period, S&P will, at its option, repair returned products or parts, or provide replacement products or parts, without charge, for any product or part which is
found to be defective under normal use.
This warranty does not cover normal maintenance and service or any parts that have been subject to misuse, negligence, accident, improper maintenance or repair, faulty
installation or installation contrary to recommended installation instructions.
S&P’s obligation to repair or replace, at S&P’s option, shall be the purchaser’s sole and exclusive remedy under this warranty. No labor or materials are covered by this
warranty. S&P shall not be liable for incidental damages arising out of or in connection with product use or performance.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
To qualify for warranty service, you must notify S&P at the address or telephone number stated below, provide the model number and part identification, and describe the
nature of any defect in product or part. You may be required to ship a defective part to S&P. There will be no charge for shipping repaired or replacement parts from S&P to
you if your address is in the United States or Canada. At the time of requesting warranty service, you must present evidence of the original purchase date.
S&P USA Ventilation Systems, LLC.
6393 Powers Avenue Jacksonville, FL 32217
P. 904-731-4711
F. 800-961-7379
www.solerpalau-usa.com
S&P Canada Ventilation Products, Inc.
6710 Maritz Drive Unit #7 Mississauga, ON L5W 0A1 - Canada
T. 416-744-1217
F. 416-744-0887
www.solerpalaucanada.com
4
