INSTALLATION INSTRUCTIONS (Continued)
Performance Testing
• Engage parking brake and start your engine.
Listen for abnormal noises. If an air leak is
detected, re-inspect hoses and connections as
they may need to be repositioned and tightened.
• S&B FILTERS recommends that you keep your
OE intake system in the event it is required in the
future.
• In order to maintain your warranty, all connections
and components must be checked periodically for
alignment and for proper tension on all
connections. Failure to do so may void your
warranty.
• Use only S&B FILTERS cleaning and oil products
to service your filter. Using any other brand oil and
or cleaners on your S&B air filter may void your
warranty.
3
P/N: 75-5053 / 75-5053D
Related Items for Your Purchase
• Replacement Air Filter (Oiled)
(S&B P/N: KF-1050)
• Replacement Air Filter (Dry)
(S&B P/N: KF-1050D)
• Air Filter Wrap (S&B P/N: WF-1031)
23.
Using the factory location, secure the
OE hose assembly using the supplied Loop
Clamp
(P)
, M6 Hex Screw
(S)
and 6mm
Washer
(R)
.
25.
Reconnect the batteries. Inspect your
installation, make sure the kit is properly
positioned and all fasteners are secure. Affix
the CARB sticker near the intake kit. The
installation is now complete.
24.
Install the Insulation Tube
(Q)
around
the factory coolant hose by removing the
protective film on the adhesive and sticking
the two sides together.
Precision II
Filter Cleaning & Oiling
Part #: 88-0008
22.
Reconnect the wiring harness to the
MAF sensor.
21.
Remove the protective covering from
the Clear Lid
(G)
, then install the lid. Start with
the 5/16” Screws
(I)
and Rubber Washers
(H)
.
Then install the 10-24 Screws
(K)
and Sealing
Washers
(J)
. Do not over tighten!
Emissions Standard
The California Air Resource Board (CARB) requires that an E.O. identification label be applied to the vehicle in order to pass a smog check inspection when a Performance
Intake Kit has been installed. You must place the E.O. label provided on or near the intake kit after installation so that a smog check technician can easily verify the E.O. number.
As of April 2009, S&B has never had a product where CARB denied an exemption request; however, the exemption process with CARB can take as long as 18 months. Check
the status of the exemption process by looking up a specific part number. The CARB Exemption number and/or status is listed under the Product Details section for each part
number. If the status shows as “Pending,” CARB has yet to issue an exemption. Products that have not been issued an EO number are street legal in most states, but may not
be used on emission controlled vehicles in the state of California and are for off road use only. If you purchased your kit from S&B Filters directly, we will automatically mail you
your Exemption Sticker when it is issued to us. If you purchased your kit from an authorized S&B Filters Dealer, log onto our web site and register to receive your Exemption
Sticker.
SEE EXPLODED VIEW ON PAGE 4
Air Box End Cap Testing
Stock air boxes are a significant contributor to
poor air flow which is why S&B designs
custom air boxes with secondary and/or
enlarged openings. With that said, S&B
recognizes the benefits of cooler air, so we
have included a plug to seal off the opening if
so desired. For optimal performance, we
recommend that the intake be used with the
end cap. Plug should also be removed during
heavy snow to keep the air box from loading
up with snow.
Warning!
If your vehicle has a Vehicle Emission Control Information decal affixed to the factory airbox, a new
replacement label must be obtained and installed in a readily visible position in the engine compartment in
order to remain CARB compliant. Failure to do so will prevent the vehicle from passing a smog check.
Replacement labels can be ordered from your local dealership. Regulations state that the VECI label shall
not be affixed to any equipment which is easily detached from the vehicle. Label placement, under the hood
on a painted surface is recommended.
