Sanctuary Platinum SA-PLAT1-BIO Instruction Manual Download Page 8

Page: 8 / 19

4. PROGRAMMING YOUR FINGERPRINT

1. On the inside of the safe door,

locate the brass cap.

Unscrew and remove the cap,

giving you access to the reset

button.

2. Press the reset button. You will

hear 1 beep and the indicator

ring will illuminate white on the

front of the door indicating that

you are now in programming

mode.

Inactivity Timeout: If this programming sequence is not completed within 10 seconds

the indicator ring will ﬂash red 5 times and beep 5 times. Return to step 2 to restart

this process.

3. PLACE AND HOLD the pad of your

ﬁnger on the scanner until indicator

ring ﬂashes green once and beeps

once.

4. REPEAT at least 3 more times until

there are 2 consecutive beeps and

2 green ﬂashes.

If unsuccesful, the indicator Ring

will ﬂash red 5 times and beep 5

times. Repeat this section again.

BEEP

HOLD FOR BEEP

LIFT FINGER

ep 2

ep 3

ep 4

BEEP

2 BEEPS + 2 GREEN FLASHES = SUCCESS!

Reset button

located

under brass

cap

WHITE LED

GREEN LED

ep 1

Summary of Contents for Platinum SA-PLAT1-BIO




















Search results

Summary of Contents for Platinum SA-PLAT1-BIO

Reviews:

Related manuals for Platinum SA-PLAT1-BIO

Brands by name

Popular brands

Sanctuary Platinum SA-PLAT1-BIO, Instruction Manual

Search results

Summary of Contents for Platinum SA-PLAT1-BIO

Reviews:

Related manuals for Platinum SA-PLAT1-BIO

Brands by name

Popular brands