Samsung Xpress C480 Series Service Manual Download Page 131

Page: 131 / 146

4. Alignment and Troubleshooting

► Error Code

U3-3313

U3-3314

► Error message

Document jam. Remove jam

► Symptom

A document jam was detected in the ADF unit.

► Troubleshooting method

1) Remove the jammed paper from ADF unit.

2) If the error persists, turn the machine off then on.

3) If the document jam occurs continually, open the ADF cover-top. Check if the ADF pick up roller is contaminated

or worn out. Clean or replace it.

4) If the pick up roller is OK, check the followings.

a) Check if the ADF motor is working normally.

b) Check if the connector on the ADF joint board is connected correctly.

5) If the problem persists, replace the ADF unit.

► Error Code

U3-4110

► Error message

Door of scanner is open.

► Symptom

ADF cover is opened.

► Troubleshooting method

1) Close the ADF cover.

4-64

Summary of Contents for Xpress C480 Series

















































































































































Search results

Summary of Contents for Xpress C480 Series

Reviews:

Brands by name

Popular brands

Samsung Xpress C480 Series, Service Manual

Search results

Summary of Contents for Xpress C480 Series

Reviews:

Brands by name

Popular brands