Samsung WA3100M PJT Service Manual Download Page 4

2 _ Safety Instructions

WHILE SERVICING

•  Check if the power plug and outlet are damaged, flattened, cut or otherwise degraded.

4

  If faulty, replace it immediately. 

Failing to do so may result in electric shock or fire.

• 

Completely remove any dust or foreign material from the housing, wiring and connection parts.

4

  This will prevent a risk of fire due to tracking and electrical hazard..

• 

When connecting wires, make sure to connect them using the relevant connectors and check that they are 
completely properly.

4

  If tape is used instead of the connectors, it may cause fire due to tracking.

• 

Make sure to discharge the PBA power terminals before starting the service.

4

  Failing to do so may result in a high voltage electric shock.

• 

When replacing the heater, make sure to fasten the nut after ensuring that it is inserted into the bracket-heater.

4

  If not inserted into the bracket-heater, it touches the drum and causes noise and electric leakage.

AFTER SERVICING

• 

Check the wiring.

4

  Ensure that no wire touches a rotating part or a sharpened part of the electrical harness.

• 

Check for any water leakage.

4

  Perform a test run for the washing machine using the standard course and check whether there is any water 

leakage through the floor section or the pipes.

• 

Do not allow consumers to repair or service any part of the washing machine 
themselves.

4

  This may result in personal injury and shorten the product lifetime.

• 

If it seems that grounding is needed due to water or moisture, make sure to run 
grounding wires. 
(Check the grounding of the power outlet, and additionally ground it to a metallic water 
pipe.)

4

  Failing to do so may result in electric shock due to electric leakage.

 

[Running a grounding wire]

Twist a grounding wire (copper wire) two or three times around the tap.

If you connect the grounding wire to a copperplate, bury it 75 cm under the earth in a 
place with a lot of moisture.

  Do not connect the grounding wire to a gas pipe, plastic water pipe or telephone 

wire. There is a risk of electric shock or explosion.

Grounding 
terminal

75 cm

Copperplate

WARNING

WARNING

Summary of Contents for WA3100M PJT




































Reviews: