background image

English  51

Tr

ouble

shoo

ting

Problem

Action

Leaks water.

• 

Make sure all hose connections are tight.

• 

Make sure the water supply hose's rubber packing is in the 
correct position. Screw tightly again.

• 

Make sure the end of the drain hose is correctly inserted and 
secured to the drain system.

• 

Avoid overloading.

• 

Use high efficiency (HE) detergent to prevent oversudsing.

• 

Make sure the water supply hose is not kinked.

• 

If the water supply is too strong, water may leak. Close the 
water tap a little.

• 

Make sure water is not leaking from the water tap. If so, 
repair the water tap.

Excessive suds.

• 

Use high efficiency (HE) detergent to prevent oversudsing.

• 

Reduce the detergent amount for soft water, small loads, or 
lightly soiled loads.

• 

Non-HE detergent is not recommended.

The spin basket or 
drain/supply hose is 
frozen.

• 

Use warm water to disconnect the water supply hose and 
drain hose. Soak them in warm water.

• 

Fill the spin basket with warm water, and then wait for about 
10 minutes.

• 

Put a hot towel on the drain hose connector.

• 

Reconnect the water supply hose and drain hose, and check if 
water is supplied properly.

Water drains out 
immediately.

• 

Make sure the drain hose is not clogged, and is hung over the 
drain hose hook. Fill the spin basket halfway with water, and 
try spinning again.

• 

Lift the end of the drain hose to prevent water from draining. 
Fill the spin basket halfway with water, and then run spinning 
after releasing the drain hose.

• 

Make sure the drain hose is installed correctly. See the 
installation section of this user manual and adjust the position 
of the drain hose as instructed.

Stains on clothes.

• 

 Clean the magic filter.

Has odours. 

• 

Excessive suds collect in recesses and can cause foul odours.

• 

Run cleansing cycles to sanitize periodically. 

• 

Dry the washing machine interior after a cycle has finished.

WA8700J_WA10J8700GP-03520B-03_SA.indd   51

2015/7/25   11:29:31

Summary of Contents for WA10J8700G Series































































Reviews: