Samsung VP-L600 Owner'S Instruction Manual Download

Page: 60 / 67

ENGLISH

Checking

Troubleshooting Check

✤

If you run into any problem using the camcorder, use the following table to try to resolve the problem.

✤

If these instructions do not allow you to solve the problem, take a note of:

■

The model and serial number marked on the bottom of the camcorder.

■

Your warranty, if applicable.

✤

Then contact your nearest authorized service centre.

Symptom

Explanation/Solution

You cannot switch the

◆

Check the battery pack (see page 19)

camcorder on.

or the AC power adapter. (see page 18)

Start/Stop does not

◆

Check the POWER, set it to CAMERA.

operate while shooting.

◆

You have reached the end of the cassette.

◆

Check the record protection tab on the cassette. (see page 22)

The camcorder goes

◆

You have left the camcorder set to STANDBY

off automatically.

for more than 5 minutes without using it.(see page 24)

◆

The battery pack is fully used up. (see page 21)

The battery pack is

◆

The atmospheric temperature is too low. (see page 21)

quickly exhausted.

◆

The battery pack has not been charged fully.(see page 19)

◆

The battery pack is completely dead, and cannot be recharged.
Use another battery pack.

You cannot eject the

◆

The battery pack is fully discharged.

cassette from the

◆

A mechanical fault may have occurred. (see page 59)

compartment.

The DATE/TIME indicator

◆

The lithium battery is not installed or is fully used up.

flashes more than 2 times

(see page 17)

when you set the
camcorder to CAMERA.

The playback picture

◆

The video heads might be dirty. (see page 57)

is in poor quality.

You can do nothing

◆

A mechanical fault may have occurred. (see page 59)

with the camcorder.

Summary of Contents for VP-L600




































































Search results

Summary of Contents for VP-L600

Reviews:

Related manuals for VP-L600

Brands by name

Popular brands

Samsung VP-L600, Owner'S Instruction Manual

Search results

Summary of Contents for VP-L600

Reviews:

Related manuals for VP-L600

Brands by name

Popular brands