Samsung UQ07P2GE Service Manual Download Page 22

Page: 22 / 54

Samsung Electronics

Troubleshooting

Indoor unit observes operation condition of the air conditioner, and displays self diagnosis details on the display panel.

5. Operation with abnormal motion

Indoor unit room temperature sensor error
(open or short)

Indoor unit heat exchanger temperature sensor error
(open or short)

Indoor fan motor malfunction

EEPROM error

Option error
(option wasn't set up or option data error)

Display

Flickering

Error Mode

LAMP

7-segment

Display

OPERATION

TIMER

TURBO

: Lamp flickering

: Lamp off

No response from

the remote control

operation signal.

Unable to operate the

outdoor unit

• Plug out and plug in 5 seconds

later.

• Press the TURBO button with the

remote control.

• In 3 minutes, check the voltage

between the indoor unit terminal

block N(1) and 1.

Able to operate the

remote control.

Unable to operate

the remote control.

AC198V ~ AC242V

No power source

displayed.

Press the

(ON/OFF) button in the

indoor unit.

• If it operates, the remote control and

indoor unit receiver are in trouble.

• If not, the indoor unit is in trouble.

Problem with the outdoor unit or PCB

Problem with the relay (RY71) or PCB

Abnormal condition

Inspection

Initial Diagnosis

DB98_16202A(4)_1 04/3/29 12:20 PM Page 21

Summary of Contents for UQ07P2GE























































Search results

Summary of Contents for UQ07P2GE

Reviews:

Brands by name

Popular brands

Samsung UQ07P2GE, Service Manual

Search results

Summary of Contents for UQ07P2GE

Reviews:

Brands by name

Popular brands