background image

Spinpoint M8 Product Manual REV 2.7

 

69 

 

 

   

Each  attribute  data  structure  is  assigned  an  attribute  ID.  Any  non-zero  value  in  the  attribute  ID  number 
indicates  an  active  attribute.  Valid  values  for  this  byte  are  found  from  0x01  through  0xff.  The  attribute 
defined for Spinpoint M8  are as follows:

  

 

Table 8-17 SMART Attribute Data List

 

 

Attribute 

ID

 

Definition

 

Monitor

 

Raw read error rate 

Errors during read operations. 

Spin up time 

Spin up time in millisecond 

Spindle motor on count 

On/off count. 

Number of Auto Reassign sectors 

Reassigned sector count. 

Seek error rate 

Errors during seek operations. 

Seek time performance 

Off-line random seek time 

Drive run time. 

How long drive works. 

10 

Spin up retry count 

Retry count 

12 

Power cycle count 

Total power cycles. 

194 

Temperature. 

Pre amp die temperature 

195 

ECC on the fly 

ECC count for read operation 

196 

Re-allocate sector event 

Read scan uncorrectable read error 

197 

Pending sector count 

Off-line scan pending sectors 

198 

Uncorrectable sector count 

Off-line scan uncorrectable sectors. 

199 

UDMA CRC error rate 

CRC Errors during UDMA transfer 

200 

Write error rate 

Errors during write operations. 

201 

Soft error rate 

Soft errors during read operations. 

 

Off-line data collection status

 

 

The  value  of  the  off-line  data  collection  status  byte  defines  the  current  status  of  the  off-line  activities  of  the 
device. Table6-15 lists the values and their respective definitions.

 

 

Table 8-18 Off-line Data Collection Status Values

 

 

Value

 

Definition

 

00h or 80h 

Off-line data collection activity was never started. 

01h 

Reserved 

02h or 82h 

Off-line data collection activity was completed without error. 

03h 

Reserved 

04h or 84h 

Off-line data collection Activity was suspended by an interrupting command from host 

05h or 85h 

Off-line data collection Activity was aborted by an interrupting command from host 

06h or 86h 

Off-line data collection Activity was aborted by the device with a fatal error. 

07h-3Fh 

Reserved 

40h-7Fh 

Vendor specific 

 

81h 

Reserved 

 

 

83h 

Reserved 

 

 

87h-BFh 

Reserved 

 

 

C0h-FFh 

Vendor specific 

 

 

 

Summary of Contents for SpinPoint M8




















































































Reviews: