Connection to Monitor
(1) Backlight Compensation (BLC)
•As a connecting method varies according to instruments, refer to the manual supplied with
the instrument.
•Connect the cable after power is turned off.
•Set the 75
Ω
/ Hi-Z selection switch. If it is a intermediate device, switch it to Hi-z and if
it is final device, switch it to 75
Ω
. (Please refer to the Monitor Manual.)
DOME Camera
Monitor
Intermediate
BNC
Connection to Power
•Connect the adapter to the power input connector as shown in the figure below. Use a
DC 12V. (The Adapter is not provided with the Dome Camera.)
Switch it to BLC to obtain the clear picture, the finest detail and perfect light
contrast althongh there is strong backlight.
•BLC ON: When the image is in front of strong background lighting, your camera allows you
to get the clear image.
•BLC OFF : Deactivate BLC control feature.
- To use BLC more effective, Adjust the subject to be over 20% of full screen.
- Switch to BLC OFF when the background has strong white.
If you have trouble operating your camera, refer to the following. If the guidelines do not
enable you to solve the problem, contact an authorized technician.
The image on the screen is dim.
• Check if the lens are stained. If dirty, clean the lens with soft, clean cloth.
• The image is dimmer at night than daytime. If the focus is not right, adjust it at daytime.
The contrast on the screen is too weak.
• Adjust the contrast feature of the monitor.
• If the camera is exposed under too strong light, change the camera position.
• Adjust the lens BACK FOCUS again.
The camera is not work properly, and the surface of the camera case is hot.
• Check that you have connected the camera to a proper power (DC12V ).
Background is too bright.
• Deactivate BLC control feature.
(2) White Balance Control (ATW/AWC)
Select the desired control mode using ATW/AWC switch.
• ATW(Auto Tracing White balance): The camera automatically controls the white
balance in any environment.
• AWC(Auto White balance Control): In order to obtain the best image, menu the
switch from ATW to AWC while the camera
focuses on white paper.
DOME Camera
Adapter (not provided)
Power Input Connector
CONFIGURATION OF DIP-SWITCHES
TROUBLESHOOTING
SPECIFICATION
DIMENSION
DECLARATION OF CONFORMITY
Use the DIP switches inside of the camera for selecting functions.
• To use BLC more effective, Adjust the subject to be over 20% of full screen.
• Switch to BLC OFF when the background has strong white.
Notes
• When installing the camera on a ceiling or a wall, not to disturb adjustment of Tilt Base angle fix
the BNC-Power Cable on the Pan Base clip.
• When installing the camera on a ceiling or a wall, fuctional selection switch should be bottom-left
and switch function demo sticker under the lens.
Notes
(4) Flickerless (SID-42C Series Only)
In this function electronic shutter speed is fixed in 1/100sec(1/120sec: PAL
model). FL function can compensate the flicker caused by power frequency,
but set OFF in the area not using a 60Hz(50Hz: PAL model) AC power.
(3) Sharpness
The switch emphasize the sharpness. To soften the edge move this Swich
to Normal.
• After loosening Pan or Tilt Base holding screws, adjust its angle. And then tighten screws again.
• AWC(Auto Balacne Control): In order to obtain the best image, mode the switch from ATW to AWC
while the camera focuses on white paper.
• In case of adjusting the tilting, do not take the lens for preventing hysical shocks. Please take the Tilt Base.
• This dome camera is to be installed on the ceiling by factory default. In case of using camera on the wall,
readjust the Tilt angle as page 7 (Notes).
Notes
Panning & Tilting Control
You can adjust the Panning and Tilting angle freely. (Panning angle: 360°,
Tilting angle: 10°~90°)
1) Adjustment Panning angle: After attaching the dome camera to a ceiling or a wall, adjust the
panning angle for better monitoring area by rotating the Pan Base. The panning angle can be
adjusted 360° freely.
2) Adjustment Tilting angle: After attaching the dome camera to a ceiling or a wall, adjust
the tilting angle for better monitoring area by rotating the Tilt Base. The tilting angle can
be adjusted to 10° from 90° freely. (based the ceiling surface)
Pan Base
You can rotate the lens from 360˚
Tilt Base Holding Screws
Tilt Base
You can adjust up and down
the camera (10°~90°).
SIC-22CN
SIC-22CP
SIC-42CN
SIC-42CP
Item
Input power
Power Consumption
Operating
& Humidity
Dimension
Weihgt
Pickup Device
Video Output
Min. illumination
Synchronizaion
S/N
Resolution
Lens (Built-in)
ESC
White Balance
BLC
Shrpness
Flickerless
Monitoring Pan
Angle Tilt
DC 12V ± 10%
1.4W 1.5W
-10C˚ ~ +50C˚ [-14˚F ~ 122˚F] / 30% ~ 90% RH
85.5mm(Ø) x 68mm(H)
160g
1/3” color interline-transfer CCD
1Vp-p Composite 75
Ω
unbalanced
0.4Lux / F1.2 0.7Lux / F1.2
INT
more than 48dB (Weight ON)
more than 330TV Line more than 480TV Line
Fixed Lens 92˚, Focal Length 3.7mm, F2.2
1/60(1/50) ~ 1/120,000sec
ATW / AWC Selectable
ON / OFF Selectable
High / Normal selectable
Not Used ON / OFF selectable
360˚
10˚ ~ 90˚
Application of Council Directive(s)
89 / 336 / EEC
Manufacturer's Name
SAMSUNG TECHWIN CO., LTD
Manufacturer's Address
SAMSUNG TECHWIN CO., LTD
42, SUNGJU-DONG CHANGWON-CITY,
KYUNGNAM, KOREA, 641-120
European Representative Name
European Representative Address
Equipment Type/Environment
MINI DOME CAMERA
Model Name
SID-42CP / 22CP
Beginning Serial NO.
S3B00001
Year of Manufacture
2003. 11. 1
Conformance to
EN 50081-1 : 1992
EMC-Directive 89/336 EEC and 92/31/EEC
EN 50130-4 : 1996
We, the undersigned, hereby declare that the equipment specified above conforms to the above
Directive(s).
Manufacturer
SAMSUNG TECHWIN CO., LTD
Legal Representative in Europe
Signature Signature
Full Name
YOUNG TAEK SON
Full Name
Position
QUALITY CONTROL MANAGER
Position
Place CHANGWON,
KOREA
Place
Date
2003. 11. 1
Date
Resistance of copper wire [at 20C˚ (68˚F)]
• As the voltage drop according to the length of the cable in the above table, a camera may
malfunction if there is an excessively long cable run.
* Voltage for camera operation: 12V DC ±10%
* Voltage drops in the above table are variable according to types of cable manufacturer.
For DC Power Type
Copper wire size (AWG) #24(0.22mm
2
) #22(0.33mm
2
)
#20(0.52mm
2
) #18(0.83mm
2
)
Resistance (
Ω
/ m)
0.078
0.050
0.030
0.018
Voltage Drop (V/m)
0.028
0.018
0.011
0.006
SID-42C Series
SID-22C Series
Connect the VIDEO-OUT jack to the VIDEO-IN jack of monitor.
MINI DOME CAMERA
USER’S MANUAL
9
MINI DOME CAMERA
USER’S MANUAL
8
MINI DOME CAMERA
USER’S MANUAL
7
MINI DOME CAMERA
USER’S MANUAL
10
MINI DOME CAMERA
USER’S MANUAL
13
MINI DOME CAMERA
USER’S MANUAL
12
MINI DOME CAMERA
USER’S MANUAL
11
Pan Base Holding Screw
Ø 85.5mm
Ø 63mm
68mm
<Installing the camera on a ceiling>
<Installing the camera on a wall>
Functional selection switch
BNC-Power Cable
Switch functional demo sticker
