Samsung SF-76x series Service Manual Download

Page: 82 / 103

4. Alignment and Troubleshooting

► Error Code

M2–1317

► Error message

Paper Jam inside machine

► Symptom

A paper jam was detected in the fuser unit area.

► Troubleshooting method

•

If the machine

supports

fax.

1) Open the top cover. Remove the jammed paper.

2) Turn the machine off.

3) Turn the machine on while pushing the cancel button. Wait for rebooting the machine.

•

If the machine

not supports

fax.

1) Open the top cover. Remove the jammed paper.

2) Entering Tech Mode : Menu # 1 9 3 4.

3) Select Data Setup.

4) Wrap Jam Clear

Select

Yes

by Ok button, and the machine is rebooted after Error Clear.

► Error Code

S2–4110

► Error message

Door open. Close it.

► Symptom

Top cover is open or the cover open switch is defective.

► Troubleshooting method

1) Check if the top cover is closed perfectly. Open and close it.

2) Remove the right cover. Check if the connection between the main board and SMPS/HVPS board is correct.

3) Check if the cover open switch on SMPS/HVPS board is operated properly. If it is defective, replace the

SMPS/HVPS board.

4-23

Summary of Contents for SF-76x series







































































































Search results

Summary of Contents for SF-76x series

Reviews:

Related manuals for SF-76x series

Brands by name

Popular brands

Samsung SF-76x series, Service Manual

Search results

Summary of Contents for SF-76x series

Reviews:

Related manuals for SF-76x series

Brands by name

Popular brands