manualshive.com logo in svg

Samsung SCW61, Service Manual

Share
Download
Samsung SCW61 Service Manual Download Page 56

Samsung Electronics

4-37

Alignment and Adjustment

Notes :

1. After each adjustment step is completed, OSD shows ÒOKÓ.
2. EEPROM stores confirmed adjustment value of each adjustment step.
3. After finishing the adjustment, reset the main power source to memorize the adjustment data in EEP-

ROM.

4. Camcorder set is used as a CVF adjust tool.

4-2-3 (a) PREPARATION

1. How to get into the CVF adjustment mode.

Note :  When XX XX is shown in service adjustment procedures, this indicates variable values.

4-2-3 CVF Adjustment

1. Connect the power source (battery/DC

cable).

2. Set the mode switch of the camcorder to

ÒCAMERA MODEÓ position.

3. Set OSD on state.
4. Press and hold the ÒTAPE EJECTÓ button

and ÒDATE/TIMEÓ button on the cam-
corder at the same time for more than 5
seconds.

Then unit goes into service mode.

STEP1

MONITOR  OSD shows ÒODF XX XXÓ. Then
CVF adjustment mode has been activated
successfully and press MODE Ô100Õ up button
4times, OSD shows Ò3F7Ó and then go back-
word to Ò3DBÓ

STEP2

3DB

EPR : XX                EVR : XX

DATA DOWN

MODE UP

MODE DOWN

DATA UP

MODE ‘100’ UP
CONFIRM

Summary of Contents for SCW61






























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands