High Resolution Compact Flat Dome Camera
8
User Guide
High Resolution Compact Flat Dome Camera
9
User Guide
High Resolution Compact Flat Dome Camera
10
User Guide
High Resolution Compact Flat Dome Camera
11
User Guide
High Resolution Compact Flat Dome Camera
12
User Guide
High Resolution Compact Flat Dome Camera
13
User Guide
High Resolution Compact Flat Dome Camera
14
User Guide
High Resolution Compact Flat Dome Camera
15
User Guide
• To facilitate the installation work, arrange the BNC-POWER cable through the wiring hole.
Notes
Connecting to Power
• Connect the adapter to the power input connector as shown in the figure below.
Use a DC 12V. (The Adapter is not provided with the Dome Camera.)
DOME Camera
Adapter (not provided)
Power Input Connector
DOME Camera
Connection to Monitor
• As a connecting method varies according to instruments, refer to the manual supplied with the instrument.
• Connect the cable after power is turned off.
Resistance of copper wire [at 20Cº(68ºF)]
• As the voltage drop according to the length of the cable in the above table, a camera may malfunction if
there is an excessively long cable run.
* Voltage for camera operation: DC 12V±10%
* Voltage drops in the above table are variable according to types of cable manufacturer.
For DC Power Type
Connect the VIDEO-OUT jack to the VIDEO-IN jack of monitor.
• If you want to adjust the lens angle, loosen the screws slightly on both sides of the lens cover to prevent
possible damage to the camera before the adjustment.
• This dome camera is to be installed on the ceiling by factory default.
• If the camera is tilted more than 90°, captured screen may be obscured.
Notes
Panning & Tilting Control
You can adjust the Panning and Tilting angle freely. (Panning angle:
±
10º, Tilting angle: 0º~90º)
1) Adjustment Panning angle: After attaching the dome camera to a ceiling, adjust the panning angle for better
monitoring area by rotating the Pan Base. The panning angle can be adjusted ±10º freely.
2) Adjustment Tilting angle: After attaching the dome camera to a ceiling, adjust the tilting angle for better
monitoring area by rotating the Tilt Base. The tilting angle can be adjusted to 0º from 90º freely. (based the
ceiling surface)
Pan Base
You can rotate the lens from
±
10º
Tilt Base
You can adjust up and down
the camera (0º~90º).
If you have trouble operating your camera, refer to the following.
If the guidelines do not enable you to solve the problem, contact an authorized technician.
◾
The image on the screen is dim.
• Check if the lens are stained. If dirty, clean the lens with soft, clean cloth.
• The image is dimmer at night than daytime. If the focus is not right, adjust it at daytime.
◾
The contrast on the screen is too weak.
• Adjust the contrast feature of the monitor.
• If the camera is exposed under too strong light, change the camera position.
• Adjust the lens BACK FOCUS again.
◾
The camera is not work properly, and the surface of the camera case is hot.
• Check that you have connected the camera to a proper power (DC 12V±10%).
Monitor
BNC
Built-in functions of the SCV-2010F Camera include the following
Camera Operation
Troubleshooting
Dimension
Specification
Specification
Copper wire size (AWG)
#24(0.22mm
2
) #22(0.33mm
2
)
#20(0.52mm
2
)
#18(0.83mm
2
)
Resistance (
Ω
/ m)
0.078
0.050
0.030
0.018
Voltage Drop (V/m)
0.028
0.018
0.011
0.006
Auto Functions
Setting
Descriptions
Electronic Shutter Speed
ESC
The shutter is controlled according to the brightness of screen by
automatically.
WHITE BALANCE
ATW
It can be used within the color temperature range 1,700K ~ 11,000K.
BACKLIGHT
OFF
It helps view a desired area of picture at the backlight condition.
GAIN CONTROL
HIGH
The gain increases or decreases within the range of 6dB~34dB.
SSNR3
(Noise Reduction)
ON
There is sufficient reduction in noise levels without causing much
ghost imaging.
SENS-UP
AUTO
It helps maintain a bright, clear screen image by automatically
detecting changes in the level in low light levels without causing much
ghost imaging.
SHARPNESS
ON
The outline of the video image becomes cleaner and more distinctive.
LENS SHADE
ON
It helps correct shading of Lens.
✽
If you need to control OSD menu, It needs coaxial controller.
SCV-2010FN
SCV-2010FP
VIDEO
Imaging Device
1/3" Super HAD CCD
Total Pixels
811(H) x 508(V)
795(H) x 596(V)
Effective Pixels
768(H) x 494(V)
752(H) x 582(V)
Scanning System
2:1 Interlace
Synchronization
Internal
Frequency
H : 15.734KHz / V : 59.94Hz
H: 15.625KHz / V : 50.00Hz
Horizontal Resolution
Color : 600 TV lines
Min. Illumination
Color : 0.04Lux (Sens-up, 2x)
S / N (Y signal)
52dB (AGC off, Weight on)
Video Output
CVBS : 1.0 Vp-p / 75Ω composite
LENS
Focal Length (Zoom Ratio)
3.0mm
Max. Aperture Ratio
F2.0
Angular Field of View
H : 89.5° / V : 67.2°
Pan / Tilt
Pan Range
±10°
Tilt Range
0° ~ 90°
OPERATIONAL
On Screen Display
Multi-language Support by Coaxial Cable
English, Japanese, Spanish, French, Portuguese,
Korean
Multi-language Support by Coaxial Cable
English, French, German, Spanish, Italian, Chinese,
Russian, Polish, Czech, Romanian, Serbian,
Swedish, Danish, Turkish, Portuguese
Camera Title
Off / On (Displayed 15 characters)
Day & Night
Auto (Electrical) / Color / B/W
Backlight Compensation
BLC / HLC / OFF
SCV-2010FN
SCV-2010FP
Dynamic Range
SSDR ( Off /On )
Digital Noise Reduction
SSNR
Ⅲ (
Off / On)
Digital Image Stabilization
Off / On
Motion Detection
Off / On (8 programmable zones)
Privacy Masking
Off / On (12 programmable zones)
Sens-up (Frame Integration)
2x ~ 512x
Gain Control
low/high/off
White Balance
ATW / Outdoor / Indoor / Manual / AWC (1,700K° ~ 11,000K°)
Electronic Shutter Speed
1/60 ~ 1/120,000 sec
1/50 ~ 1/120,000 sec
Digital Zoom
Off / On (1x ~ 16x)
Flip / Mirror ( Reverse )
H-Rev ( Off/On ), V-Rev ( Off/On )
Communication
Coaxial Control (SPC-300 compatible)
Protocol
Pelco-C (Coaxitron)
ENVIRONMENTAL
Operating Temperature / Humidity
-10°C ~ +50°C (+14°F ~ +122°F) / Less than 90% RH
ELECTRICAL
Input Voltage
DC 12V±10%
Power Consumption
1.8W
MECHANICAL
Color/Material
Body : Ivory / Aluminum
Dimension (W X H X D)
W125.2 x H52 x D115.2mm
Weight
410g
Water Resistance
IP 66
※
The specification for this product may change without prior notice for product improvement.
BNC-Power Cable
MEMO
