background image

English_5

  

SAFETY INFORMATION


t.

e, 

Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers 
fi lled with water on top of the camera. doing so may cause personal injury due to fi re, electric 
shock, or falling objects.

Do not install the unit in humid, dusty, or sooty locations. doing so may cause fi re or electric 
shock.

If any unusual smells or smoke come from the unit, stop using the product. in such case, 
immediately disconnect the power source and contact the service center. continued use in 
such a condition may cause fi re or electric shock.

If this product fails to operate normally, contact the nearest service center. never disassemble 
or modify this product in any way. (samsung is not liable for problems caused by unauthorized 
modifi cations or attempted repair.)

  When cleaning, do not spray water directly onto parts of the product. doing so may cause 

fi re or electric shock.

CAUTION

Do not drop objects on the product or apply strong shock to it. Keep away from a location 
subject to excessive vibrationor magnetic interference.

Do not install in a location subject to high temperature (over 55°C), low temperature (below 
-30°C), or high humidity. Doing so may cause fi re or electric shock.

If you want to relocate the already installed product, be sure to turn off the power and then 
move or reinstall it.

Remove the power plug from the outlet when then there is a lightning. Neglecting to do so 
may cause fi re or damage to the product.

Keep out of direct sunlight and heat radiation sources. It may cause fi re.

Install it in a place with good ventilation.

Avoid aiming the camera directly towards extremely bright objects such as sun, as this may 
damage the CMOS image sensor.

Apparatus shall not be exposed to dripping or splashing and no objects fi lled with liquids, 
such as vases, shall be placed on the apparatus.

The Mains plug is used as a disconnect device and shall stay readily operable at any time.

  Do not expose the camera to radioactivity. Radioactivity exposure may damage the 

CMOS.

6.

7.

8.

9.

10.

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

Summary of Contents for SCO-6083R



































Reviews: