background image

2

ENG

3

9.  If this product fails to operate normally, 

contact the nearest service center. Never 

disassemble or modify this product 

in any way. (SAMSUNG is not liable 

for problems caused by unauthorized 

modifications or attempted repair.)

10.  When cleaning, do not spray water 

directly onto parts of the product. Doing 

so may cause fire or electric shock.

CAUTION

1.  Do not drop objects on the product or 

apply strong shock to it. Keep away from 

a location subject to excessive vibration 

or magnetic interference. 

2.  Do not install in a location subject to 

high temperature (over 122°F), low 

temperature (below 14°F), or high 

humidity. Doing so may cause fire or 

electric shock. 

3.  If you want to relocate the already 

installed product, be sure to turn off the 

power and then move or reinstall it. 

4.  Remove the power plug from the 

outlet when then there is a lightning. 

Neglecting to do so may cause fire or 

damage to the product.

5.  Keep out of direct sunlight and heat 

radiation sources. It may cause fire.

6.  Install it in a place with good ventilation.

7.  Avoid aiming the camera directly towards 

extremely bright objects such as sun, 

as this may damage the CCD image 

sensor.

8.  Apparatus shall not be exposed to 

dripping or splashing and no objects 

filled with liquids, such as vases, shall be 

placed on the apparatus.

9.  The Mains plug is used as a disconnect 

device and shall stay readily operable at 

any time.

FCC Statement

This device complies with part 15 of the FCC 

Rules. Operation is subject to the following 

two conditions:

1)  This device may not cause harmful 

interference, and 

2)  This device must accept any interference 

received including interference that may 

cause undesired operation.

Note

This equipment has been tested and found to 

comply with the limits for a Class A digital device, 

pursuant to part 15 of FCC Rules. These limits 

are designed to provide reasonable protection 

against harmful interference when the equipment 

is operated in a commercial environment. This 

equipment generates, uses, and can radiate 

radio frequency energy and, if not installed 

and used in accordance with the instruction 

manual, may cause harmful interference to radio 

communications. Operation of this equipment 

in a residential area is likely to cause harmful 

interference in which case the user will be 

required to correct the interference at his own 

expense.

AB68-00647D(01)Eng.indd   3

2007-05-14   ソタネト 4:33:03

Summary of Contents for SCC-B5310N





















Reviews: