MINI CAMERA
User Guide
12
MINI CAMERA
User Guide
13
MINI CAMERA
User Guide
14
MINI CAMERA
User Guide
15
MINI CAMERA
User Guide
11
MINI CAMERA
User Guide
10
MINI CAMERA
User Guide
9
MINI CAMERA
User Guide
8
• When installing the camera on a ceiling, note that not to damage or squeeze the cables.
Notes
Connecting to Power
• Connect the adapter to the power input connector as shown in the figure below.
Use a DC 12V. (The Adapter is not provided with the Camera.)
MINI Camera
Power Input Connector
MINI Camera
Connection to Monitor
• As a connecting method varies according to instruments, refer to the manual supplied
with the instrument.
• Connect the cable after power is turned off.
Resistance of copper wire [at 20C
º
(68
º
F)]
• As the voltage drop according to the length of the cable in the above table,
a camera may malfunction if there is an excessively long cable run.
* Voltage for camera operation: 12V DC ±10%
* Voltage drops in the above table are variable according to types of cable manufacturer.
For DC Power Type
Connect the VIDEO-OUT jack to the VIDEO-IN jack of monitor.
• In case of adjusting the tilting, do not take the lens for preventing hysical shocks. Please take the Tilt Base.
• This camera is to be installed on the ceiling by factory default.
Notes
Panning & Tilting Control
You can adjust the Panning and Tilting angle freely. (Panning angle: 0
º
-60
º
, Tilting
angle: 0
º
~175
º
)
1) Adjustment Panning angle: After attaching the camera to a ceiling, adjust the panning
angle for better monitoring area by rotating the Pan Base. The panning angle can be
adjusted by 0
º~
60
º
.
2) Adjustment Tilting angle: After attaching the camera to a ceiling, adjust the tilting
angle for better monitoring area by rotating the Tilt Base. The tilting angle can be
adjusted from 0
º to
175
º
freely. (based the ceiling surface)
Pan Base
You can rotate the lens by
0
º
~60
º
Tilt Base
You can adjust up and down
the camera (0
º
~175
º
).
If you have trouble operating your camera, refer to the following.
If the guidelines do not enable you to solve the problem, contact an authorized
technician.
◾
The image on the screen is dim.
• Check if the lens are stained. If dirty, clean the lens with soft, clean cloth.
•
The image is dimmer at night than daytime. If the focus is not right, adjust it at daytime.
◾
The contrast on the screen is too weak.
• Adjust the contrast feature of the monitor.
• If the camera is exposed under too strong light, change the camera position.
• Adjust the lens BACK FOCUS again.
◾
The camera is not work properly, and the surface of the camera case is hot.
• Check that you have connected the camera to a proper power (DC 12V).
Monitor
BNC
Built-in functions of the SCB-2010 Camera include the following
✽
If you need to control OSD menu, It needs coaxial controller.
Camera Operation
Troubleshooting
Dimension
Specification
Specification
Copper wire size (AWG)
#24(0.22mm
2
) #22(0.33mm
2
)
#20(0.52mm
2
)
#18(0.83mm
2
)
Resistance (
Ω
/ m)
0.078
0.050
0.030
0.018
Voltage Drop (V/m)
0.028
0.018
0.011
0.006
Auto Functions
Setting
Descriptions
Electronic Shutter
Speed
ESC
The shutter is controlled according to the
brightness of screen by automatically.
WHITE BALANCE
ATW
It can be used within the color temperature
range 1,700K ~ 11,000K.
BACKLIGHT
OFF
It helps view a desired area of picture at the
backlight condition.
GAIN CONTROL
HIGH
The gain increases or decreases within the
range of 6dB~34dB.
SSNR3
(Noise Reduction)
ON
There is sufficient reduction in noise levels
without causing much ghost imaging.
SENS-UP
AUTO
It helps maintain a bright, clear screen image by
automatically detecting changes in the level in
low light levels without causing much ghost
imaging.
SHARPNESS
ON
The outline of the video image becomes cleaner
and more distinctive.
LENS SHADE
ON
It helps correct shading of Lens.
SCB-2010N
SCB-2010P
ELECTRICAL
Input Voltage
DC 12V ±10%
Power Consumption
Max 1.8W
VIDEO
Imaging Device
1/3 inch, Sony Super HAD CCD
II
Total Pixels
811(H) x 508(V)
795(H) x 596(V)
Effective Pixels
768(H) x 494(V)
752(H) x 582(V)
Scanning System
2:1 Interlace
Synchronization
Only Internal
Frequency
H : 15.734KHz V : 59.94Hz
H: 15.625KHz V : 50.00Hz
Horizontal
Resolution
color: 600TVL
Min. Illumination
color: 0.04 Lux (50 [email protected], Sens-up 2x)
S / N (Y signal)
52dB (Weight On, AGC Off)
Video Output
CVBS : 1.0Vp-p, 75Ω composite
LENS
Focal Length
3mm
Angular Field of View
H : 95°, V : 71°
Max. Aperture Ratio
F2.0
Min. Object Distance
0.4m
PAN / TILT
Pan / Tilt Range
0° ~ 60° / 0° ~ 175°
OPERATIONAL
Shutter Mode
ESC, A.FLK, Manual
Lens Shade
On / Off (Level adjustable)
SSDR
On / Off (Level adjustable)
※
The specification for this product may change without prior notice for product improvement.
Backlight
Compensation
USER BLC / HLC / OFF
Day & Night
COLOR / BW / AUTO (Electric Type)
Gain Control
Low / High / Off
White Balance
ATW / Outdoor / Indoor / Manual / AWC (1,700°K ~ 11,000°K)
SENS-UP
Auto / Off (Selectable x2 ~ x512)
Motion Detection
On / Off (8 Programmable zones)
Privacy Masking
On / Off (12 Programmable zones)
SSNR3
On / Off (Level adjustable)
Digital Zoom
On / Off (x1 ~ x16)
DIS
On / Off
Camera Title
On / Off (Displayed 15 Characters)
Sharpness
On / Off (Level adjustable)
Flip / Mirror
On / Off
Communication
Coaxial (Pelco Coaxitron)
Electronic Shutter Speed
1/60 ~ 1/120,000 sec
1/50 ~ 1/120,000 sec
On Screen Display
English, Korean, Japanese, Spanish,
French, Portuguese, Taiwanese
English, Chinese, German, Italian,
French, Spanish, Russian, Czech, Polish,
Romanian, Serbian, Swedish, Danish,
Turkish, Portuguese
ENVIRONMENTAL
Operating Temperature /
Humidity
-10°C ~ +50°C (+14°F ~ +122°F) / Less than 90% RH
MECHANICAL
Color/Material
Ivory/Plastic
Dimension(W x H x D)
52 x 52 x 40.4mm(without bracket)
52 x 52 x 81.4mm(with bracket)
Weight
95g (with bracket)
BNC-Power Cable
UNIT: mm(inch)
0°~175°
0°~60°
----
Power Input
Terminal
