Samsung SCA20 Service Manual Download Page 47

Page: 47 / 134

Alignment and adjustment

Samsung Electronics

5-17

12. B-Y Negative Gain

1) Camera ÒE-EÓ, 3100¡K color bar chart.
2) Video(output) jack and register of EEPROM.
3) Connect video(output) jack to waveform monitor

input jack and monitor TV jack respectively.

4) Press the ÒBLC (MODE UP)/FADE

(MODE DOWN)Ó button so that the OSD state is
Ò37 CBGN XX XXÓ.

5) Aim the camera at a color bar chart illuminated at

1500 to 2000 lx.

6) Adjust the Ò + (DATA UP)/ - (DATA DOWN)Ó

button so that the yellow level is 50IRE.

7) Be sure to press the ÒSTART/STOP (CONFIRM)Ó

button to memorize setting.

8) The OSD shows ÒOK!Ó.

13. R-Y Positive Hue

1) Camera ÒE-EÓ, 3100¡K color bar chart.
2) Video(output) jack and register of EEPROM.
3) Connect video(output) jack to vectorscope input

jack and monitor TV jack respectively.

4) Press the ÒBLC (MODE UP)/FADE

(MODE DOWN)Ó button so that the OSD state is
Ò39 CBHN XX XXÓ.

5) Aim the camera at a color bar chart illuminated at

1500 to 2000 lx.

6) Adjust the Ò + (DATA UP)/ - (DATA DOWN)Ó

button so that the red vector is 104.

7) Be sure to press the ÒSTART/STOP (CONFIRM)Ó

button to memorize setting.

8) The OSD shows ÒOK!Ó.

RED VECTOR
104 DEG.

50IRE

14. R-Y Negative Hue

1) Camera ÒE-EÓ, 3100¡K color bar chart.
2) Video(output) jack and register of EEPROM.
3) Connect video(output) jack to vectorscope input

jack and monitor TV jack respectively.

4) Press the ÒBLC (MODE UP)/FADE

(MODE DOWN)Ó button so that the OSD state is
Ò38 CHGR XX XXÓ.

5) Aim the camera at a color bar chart illuminated at

1500 to 2000 lx.

6) Adjust the Ò + (DATA UP)/ - (DATA DOWN)Ó

button so that the cyan vector is 284.

7) Be sure to press the ÒSTART/STOP (CONFIRM)Ó

button to memorize setting.

8) The OSD shows ÒOK!Ó.

CYAN VECTOR
284 DEG.

Summary of Contents for SCA20







































































































































Search results

Summary of Contents for SCA20

Reviews:

Related manuals for SCA20

Brands by name

Popular brands

Samsung SCA20, Service Manual

Search results

Summary of Contents for SCA20

Reviews:

Related manuals for SCA20

Brands by name

Popular brands