background image

- IF YOU HAVE A PROBLEM

7

CHANGE THE BATTERY(OPTIONAL)

WARNING

1. Never disassemble or recharge the batteries.
2. Never heat up the batteries or throw them into fire.
3. Do not reverse (+),(-) poles.
4. Dispose of the batteries properly.

NOTE

1.  When the vacuum cleaner does not work, replace the batteries. 

If the problem persists, please contact our authorized dealer.

2. Use 2 batteries of size AA.

BATTERY TYPE :  AA Size

10

PROBLEM

CAUSE

REMEDY

Motor does not start.

No power supply.
Thermal cut-out.

Check cable, plug and 
socket.
Leave to cool.

Suction force is gradually 
decreasing.

Nozzle, suction hose or 
tube is blocked.

Check for blockage and 
remove it.

Cord does not rewind fully.

Check that the cord is not 
twisted or wound unevenly.

Pull the cord out 2-3m and 
push the cord rewind but-
ton.

Vacuum cleaner does not
pick up dirt.

Crack or hole in hose.

Check hose and replace if 
required.

Low or decreasing suction 

Filter is  full of dust. 

Please check filter and, if 
necessary, clean as illus-
trated in the instructions. 

DJ68-00321A (EN) (0.7).indd   11

DJ68-00321A (EN) (0.7).indd   11

2011.12.26   10:47:47 AM

2011.12.26   10:47:47 AM

Summary of Contents for SC8400 SERIES













Reviews: