background image

English

User servicing manual

1.

You can check where to buy replacement parts at 

http://samsung.com/support

 

2.

Visit the part purchase site and enter the model code of your product to check the parts

 

available for purchase. The model code is labelled on the outer side of your product.

- You can check the model code and version on the barcode label at the bottom left of

 

the product.

3.

For replacement parts, make sure the part name matches that of the illustration in this

 

manual.

- User-serviceable parts are limited to handles (some models only), gaskets, drawers, and

 

hinges.

NOTE

Following the repair by a non-authorised service provider, self-repair or non-professional 
repair of the product, Samsung is not liable for any damage to the product, any injury or 
any other product safety issue caused by any attempt to repair the product which does 
not carefully follow these repair and maintenance instructions. Any damage to the product 
caused by an attempt to repair the product by any person other than a Samsung certified 
service provider will not be covered by the warranty.

CAUTION

The part name listed on the site may differ from that in this manual. Please make sure
you choose the right part name.

Replacing hinges requires extreme caution because it involves detaching the door.

Be sure to wear safety gloves while making repairs.

RB7300T_User-servicing-manual_EN.indd   1

10/15/2020   3:39:13 PM

Summary of Contents for RS50N3513SA









Reviews: