Samsung NX300 Service Manual Download Page 68

Page: 68 / 102

7-9

Firmware update

7-4 How to recover the MAIN PCB

1. Remove the screws and remove the back cover.

2. Download the latest firmware file and one recovery files and copy them to the SD card.

3. Connect the connector of back cover to MAIN PCB.
Insert the fully charged battery and SD card into the camera.

4. Short out opener pad, which is boot terminal point of TP with tweezer
as indicated in red circle. It has been up.
Then press the power button to turn on the camera.

5. LED will turn on when power is on. Then remove the tweezer.

6. LED will blink when tweezer is removed.
Then MAIN PCB recovery process will proceed. It will takes about 2 to 3 minutes.

7. LED will turn off when the recovery process is complete.

8. Turn on the camera. You may resume using the camera.

It is not necessary to go over all the adjustment process again since the existing adjustment data is not deleted.

CAUTION

■

This section describes how to recover the MAIN PCB when camera stops functioning due to power failure or some other reasons

during the firmware process.

Fig. 7-13

1. SD card less than 1GB

(It is recommended to use a SD card with less than 1GB. Occasionally a device may not read a SD card.

Attempt to use different types of SD cards.)

2. Tweezer (It is used to short out the TP on MAIN PCB.)

3. The latest firmware files such as nx300.bin

You can download the latest firmware file from the K-zone or Samsung website.

4. recovery file such as dnloader.bin

Note that the name of the firmware file may vary depending on NX model.

You will need:

MAIN PCB recovery instruction:

Summary of Contents for NX300



































































































Search results

Summary of Contents for NX300

Reviews:

Brands by name

Popular brands

Samsung NX300, Service Manual

Search results

Summary of Contents for NX300

Reviews:

Brands by name

Popular brands