background image

3

General information

IMPORTANT SAFETY INSTRUCTIONS

This product requires a three-prong grounded 

outlet. The installer must perform a ground 

continuity check on the power outlet box before 

beginning the installation to insure that the 

outlet box is properly grounded. If not properly 

grounded, or if the outlet box does not meet 

electrical requirements noted (under ELECTRICAL 

REQUIREMENTS), a qualified electrician should be 

employed to correct any deficiencies.

Insure proper
ground exists
before use

CAUTION: For personal 

safety, remove house 

fuse or open circuit 

breaker before 

beginning installation 

to avoid severe or fatal 

shock injury.

CAUTION: For personal safety, the mounting 

surface must be capable of supporting the 

cabinet load, in addition to the added weight 

of this 69 pound product, plus additional oven 

loads of up to 50 pounds or a total weight of 

109 pounds.

CAUTION: For personal safety, this product 

cannot be installed in cabinet arrangements 

such as an island or a peninsula. It must be 

mounted to BOTH a top cabinet AND a wall.

NOTE: For easier installation and personal 

safety, it is recommended that two people 

install this product.

IMPORTANT – PLEASE READ CAREFULLY. 

FOR PERSONAL SAFETY, THIS APPLIANCE 

MUST BE PROPERLY GROUNDED TO AVOID 

SEVERE OR FATAL SHOCK.

Insure proper
ground exists
before use

Insure proper 

ground exists 

before use.

The power cord of this 

appliance is equipped 

with a three-prong 

(grounding) plug which 

mates with a standard 

three-prong (grounding) 

wall receptacle to 

minimize the possibility 

of electric shock hazard 

from this appliance.

You should have the wall receptacle and circuit 

checked by a qualified electrician to make sure 

the receptacle is properly grounded.

If you have a standard two-prong wall 

receptacle, it is very important to have it 

replaced with a properly grounded three-

prong wall receptacle, installed by a qualified 

electrician.

DO NOT, UNDER ANY CIRCUMSTANCES, CUT, 

DEFORM OR REMOVE ANY OF THE PRONGS 

FROM THE POWER CORD. DO NOT USE WITH 

AN EXTENSION CORD.

ELECTRICAL 

REQUIREMENTS

Product rating is 120 volts AC, 60 Hertz, 13 amps 

and 1.5 kilowatts.This product must be connected to 

a supply circuit of the proper voltage and frequency. 

Wire size must conform to the requirements of the 

National Electrical Code or the prevailing local code 

for this kilowatt rating. The power supply cord and 

plug should be brought to a separate branch circuit 

single grounded outlet of at least 15 A and max 

of 20 A. The outlet box should be located in the 

cabinet above the microwave oven. The outlet box 

and supply circuit should be installed by a qualified 

electrician and conform to the National Electrical 

Code or the prevailing local code.

SMH1927_XAC_DE68-04108B-02_EN.indd   3

2017-11-02     2:28:59

Summary of Contents for ME21M706BAS









































Reviews: