Samsung ME16A4021AB Installation Instructions Manual Download Page 12

Page: 12 / 20

Step-by-step installation guide

A1. INSTALLATION PROCEDURE

FOR EXHAUST ADAPTOR AND

PROPER DAMPER OPERATION

CHECK

Blower Plate

Damper

Exhaust Adaptor

Retaining Hooks

Back of

Microwave

Oven

. Slide exhaust adaptor following the instructions

show in diagram.

. Make sure tape securing damper is removed

and damper pivots easily before mounting

microwave.

• You will need to make adjustments to assure

proper alignment with your house exhaust duct

after the microwave is installed.

A2. ADJUST THE EXHAUST ADAPTOR

Open the top cabinet and adjust the exhaust adaptor

to connect to the house duct.

Damper

For Side-toSide

Adjustment,

Slide the Exhaust

Adaptor as Needed

Back of

Microwave

Oven

NOTE

: The house duct is needed to connect to the

exhaust adaptor after installation completion.

House Duct

B. RECIRCULATING (NON-

VENTED DUCTLESS)

B1. ADAPTING MICROWAVE BLOWER

FOR RECIRCULATION

. Remove and save screw that holds blower plate

to microwave.

. Lift up the blower plate.

Back of

Microwave Oven

Blower

Retaining

Screws

NOTE

: The exhaust adaptor with damper is not

needed for recirculating models. You may want to

save them for possible future use.

. Remove screw holds blower mortor and carefully

pull out the blower unit. The wires will extend far

enough to allow you to adjust the blower unit.

CAUTION

: Do not touch blade of blower for

preventing crack and break. Hold outer case when

the blower pull out or back into.

A. OUTSIDE TOP EXHAUST (VERTICAL DUCT)

SMH8165_XAA_DE68-03587A-10_EN.indd 12

6/19/2019 3:44:36 PM

Summary of Contents for ME16A4021AB





















Search results

Summary of Contents for ME16A4021AB

Reviews:

Related manuals for ME16A4021AB

Brands by name

Popular brands

Samsung ME16A4021AB, Installation Instructions Manual

Search results

Summary of Contents for ME16A4021AB

Reviews:

Related manuals for ME16A4021AB

Brands by name

Popular brands