background image

4

GETTING STARTED

PRECAUTIONS

Ensure that the AC power supply in your house complies with the power requirements listed on the identification sticker 

located on the back of your product. Install your product horizontally, on a suitable base (furniture), with enough space 

around it for ventilation (3~4 inches). Make sure the ventilation slots are not covered. Do not place the unit on amplifiers 

or other equipment which may become hot. This unit is designed for continuous use. To fully turn off the unit, 

disconnect the AC plug from the wall outlet. Unplug the unit if you intend to leave it unused for a long period of time.

3.9 inch

3.9 inch

2.7 inch

3.9 inch

WARNING: DO NOT INGEST BATTERY. CHEMICAL BURN HAZARD. The remote control supplied with 

this product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause 

severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from 

children. If the battery compartment does not close securely, stop using the remote and make sure to 

keep it away from children. If you think the battery might have been swallowed or placed inside any part of the body, 

seek immediate medical attention.

During thunderstorms, disconnect the AC plug from the 

wall outlet. Voltage peaks due to lightning could damage 

the unit.

Protect the product from moisture (i.e. vases), and 

excess heat (e.g. a fireplace) or equipment creating 

strong magnetic or electric fields. Unplug the power 

cable from the AC wall socket if the unit malfunctions. 

Your product is not intended for industrial use. It is for 

personal use only. Condensation may occur if your 

product has been stored in cold temperatures.  

If transporting the unit during the winter, wait 

approximately 2 hours until the unit has reached room 

temperature before using.

Do not expose the unit to direct sunlight or other heat 

sources. This could lead to overheating and cause the 

unit to malfunction.

The battery used with this product contains chemicals 

that are harmful to the environment. Do not dispose of 

the battery in the general household trash. Do not 

expose the battery to excess heat, direct sunlight, or fire. 

Do not short circuit, disassemble, or overheat the battery. 

Danger of explosion if the battery is replaced incorrectly. 

Replace only with the same or equivalent type.

Summary of Contents for HW-J4000




































Reviews: