Samsung HPL5025 Owner'S Instructions Manual Download Page 55

Page: 55 / 72

Fine Tuning (Phase)

Preset:

• Press the RGB button to select the PC mode.

Press the Menu button. Move the joystick up or
down to select the SETUP, then press the joystick to
enter.

Move the joystick up or down to select the “Image
Lock”, then move the joystick left or right to enter.

Move the joystick up or down to select the “Phase”.

Remove picture noise (vertical stripes) on the screen
by moving the joystick left or right.
(If phase is not set properly, the picture may be
blurry.)

Press the Menu button to exit.

Position

Language

English

Scaling

Wide

Zoom/Panning

Image Lock

Miscellaneous

Move Adjust Exit

Position

Language

English

Scaling

Wide

Zoom/Panning

Image Lock

Miscellaneous

Move Adjust Exit

Auto Adjustment

Frequency

Phase

Move Adjust Exit

Phase

BN68-00263B-3 1/12/06 11:19 AM Page 55

Summary of Contents for HPL5025









































































Search results

Summary of Contents for HPL5025

Reviews:

Brands by name

Popular brands

Samsung HPL5025, Owner'S Instructions Manual

Search results

Summary of Contents for HPL5025

Reviews:

Brands by name

Popular brands