Samsung GT-E1225F Service Manual Download Page 19 | Manualshive

Page: 19 / 65

background image

SAMSUNG Proprietary-Contents may change without notice

Level 2 Repair

7-2

This Document can not be used without Samsung's authorization

1) Be careful not to make scratch and molding damage!

1) Be careful not to make scratch and molding damage!

1) Be careful not to make scratch and molding damage!

2) Be careful speaker contact pin damage!

1) Be careful not to make scratch and molding damage!

2) Be careful motor contact pin damage!

Disassemble the SHIELD CAN

Separate the KEYPAD from the FRONT

Separate the MOTOR from the REAR.

Separate the SPEAKER from the REAR.

«
...
17
18
19
20
21
...
»

Summary of Contents for GT-E1225F


































































Reviews:

No comments

Related manuals for GT-E1225F

Brand: Panasonic Pages: 20

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 289

Brand: Panasonic Pages: 60

Brand: Panasonic Pages: 68

Brand: Panasonic Pages: 36

T-Mobile KX-HDV130

Brand: Panasonic Pages: 35

Brand: Panasonic Pages: 6

Brand: Panasonic Pages: 11

Brand: Panasonic Pages: 8

KXDT346 - DIGITAL PROPRIETARY TELEPHONE

Brand: Panasonic Pages: 5

KXDT321 - DIGITAL PROPRIETARY TELEPHONE

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 24

DECT Portable Station KX-TCA256

Brand: Panasonic Pages: 12

Brand: Panasonic Pages: 18

OFFICESERV 100 Series

Brand: Samsung Pages: 42

Brand: Aastra Pages: 2

Brand: D-Link Pages: 58

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands