Samsung FlexDry DVE55M9600W User Manual Download Page 20

Page: 20 / 80

Installation

English

Alcove or closet installations

WARNING

• The dryer must be exhausted to the outside to reduce the risk of fire when installed in

an alcove or closet.

• No other fuel-burning appliance should be installed in the same closet as the dryer.
• Place the dryer at least 18 in. (460 mm) above the floor for garage installation.

Minimum clearances between the dryer and adjacent walls or other surfaces:

Sides

1 in. (25 mm)

Rear

5.9 in. (150 mm)

Top

21 in. (533 mm)

Closet front

2 in. (51 mm)

Installation with pedestal

53.7 in. (1365 mm)

27 in. (686 mm)

32.5 in. (825 mm)

46.9 in. (1192 mm)

5.9 in. (150 mm)

52.2 in. (1326 mm)

DC68-03381H-13_IB_FlexDry_DM9600M_EN_230705.indd 20

2023-06-28 6:09:06

Summary of Contents for FlexDry DVE55M9600W

















































































Search results

Summary of Contents for FlexDry DVE55M9600W

Reviews:

Related manuals for FlexDry DVE55M9600W

Brands by name

Popular brands

Samsung FlexDry DVE55M9600W, User Manual

Search results

Summary of Contents for FlexDry DVE55M9600W

Reviews:

Related manuals for FlexDry DVE55M9600W

Brands by name

Popular brands