Samsung DVD-611, Service Manual

Page: 8 / 115

Samsung Electronics 2-1
2. Reference Information
2-1 IC Descriptions
2-1-1 AIC1 (AK4393 ; Digital-to-Analog Converter)
Serial
Input
Interface
De-emphasis
Control
De-emphasis
Soft Mute
De-emphasis
Soft Mute
Left Channel
Right Channel
8X
Interpolator
8X
Interpolator
Multi-bit ˘•
Modulator
Multi-bit ˘•
Modulator
Switched
Capacitor Filter
Switched
Capacitor Filter
Control
Register
Double
Speed Select
Soft Mute
Power Down
Serial Data
Bit Clock
Left/Right Clock
Serial
Input Control
Clock Divider
Master Clock Clock Control
Left Output -
Left
Right Output -
Right
DVSS
DVDD
MCLK
PD
BICK
SDATA
LRCK
SMUTE
DFS
DEM0
DEM1
DIF0
1
2
3
4
5
6
7
8
9
10
11
12
DIF1
13
DIF2
CKS2
CKS1
CKS0
P/S
VCOM
AOUTL+
AOUTL-
AOUTR+
AOUTR-
AVSS
AVDD
VREFH
VREFL
BVSS
14
28
27
26
25
24
23
22
21
20
19
18
17
16
15
No. Pin Name I/O Pin Function and Description
1 DVSS - Digital Ground. Digital ground is 0V.
2 DVDD - Digital Supply. 3.3V or 5.0V nominal.
3 MCLK I Master Clock Input.
4 PD I Power-down and Reset. When low the AK4393 is in Power-down Mode and held in reset.
The AK4393 should always be reset after power-up.
5 BICK I Audio Serial Data Clock Input. A clock input of 64fs or more is recommended.
6 SDATA I Serial Data Input.
7 LRCK I Left/Right Clock Input. Defines the sampling rate, F
s
.
8 SMUTE
(or CS)
I Soft Mute Input or Chip Select Input. If the P/S pin (pin 25) is high, SMUTE controls the
soft mute function as follows:
- When SMUTE goes high, the soft mute cycle is initiated.
- When SMUTE goes low, the output mute is slowly released.
If the P/S pin is low, SMUTE is the Chip Select Input for the Serial Control Mode. Chip
select is active when SMUTE is low.
9 DFS I Double Sampling Speed Input. When low, this pin defines the Normal Speed Mode, and
128 x F
s
oversampling is implemented. When high, the DFS pin defines the Double Speed
Mode, implemented with 64 x F
s
oversampling. This pin features an internal pull-down.
10 DEM0
(or CCLK)
I De-emphasis Enable #0 or Control Data Clock Input. If the P/S pin (pin 25) is high,
DEM0 is used to select the De-emphasis Mode according to Table 3. If the P/S pin os low
DEM0 is the clock input for the Serial Control Mode.
11 DEM1
(or CDTI)
I De-emphasis Enable #1 or Control Data Input. If the P/S pin (pin 25) is high, DEM1 is
used to select the De-emphasis Mode according to Table 3. If the P/S pin is low, DEM1 is
the control data input for the Serial Control Mode.
12 DIF0 I Digital Input Format Select #0.
13 DIF1 I Digital Input Format Select #1.
14 DIF2 I Digital Input Format Select #2.
15 BVSS - Substrate Ground Pin. Substrate ground is 0V.
16 VREFL I Low Level Voltage Reference Input. Normally connected to analog ground.
17 VREFH I High Level Voltage Reference Input. Normally connected to analog supply.
18 AVDD - Analog Supply. Analog supply is 5V nominal.
19 AVSS - Analog Ground. Analog ground is 0V.
20 AOUTR- O Right Channel Negative Output.
21 AOUTR+ O Right Channel Positive Output.
22 AOUTL- O Left Channel Negative Output.
23 AOUTL+ O Left Channel Positive Output.
24 VCOM O Common Voltage Output. Common voltage output is 2.6V nominal.
25 P/S I Parallel/Serial Control Mode Select Input. If Low, the Serial Control Mode is
implemented. If High, the Parallel Control Mode is selected. This pin has an internal
pull-up.
26 CKS0 I Master Clock Select #0.
27 CKS1 I Master Clock Select #1.
28 CKS2 I Master Clock Select #2.