Samsung DS 24D User Instruction Download Page 20

Page: 20 / 131

DS 616

USER INSTRUCTIONS

TECHNICAL MANUAL

PART 1 JUNE 2004

1.19

1.16 ALARM REMINDER WITH MESSAGE

Station users can have two alarms programmed at their phones. Each alarm may be
one of the following three types:

0. NOTSET

The alarm is not set.

1. TODAY ONLY The alarm will ring at the programmed time and be canceled

automatically.

2. DAILY

The alarm will ring each day at this time.

In addition, each alarm may be accompanied by a 16 character message that will be
displayed while the alarm is ringing.

NOTE: These are the same two alarms described in

Alarm Reminder

. This procedure

allows a message to be added. A display keyset is necessary to view messages.

ACTION

DISPLAY

1. Press

the

Transfer key

followed by

116

Display shows

[201] ALM REM(1)
HHMM:

NOTSET

2. Dial

–

to select the alarm (e.g.,

)

[201] ALM REM(1)
HHMM:

NOTSET

Press

DOWN

to select the alarm

Press the right soft key to move the cursor

3. Enter the alarm time in 24 hour clock format

(e.g.,

1300

)

[201] ALM REM (2)
HHMM:1300

NOTSET

Display automatically advances to step 4

4. Dial the valid entry from the above list for the

alarm type

[201] ALM REM
HHMM:1300

DAILY

Press

DOWN

to select the alarm type

Press the right soft key to move the cursor

5. Enter messages using the method in

Programming Your Station’s Name

[201] ALM REM
TAKE MEDICATION

Press the right soft key to return to step 2

6. Press

the

Transfer key

to store and exit

Home Page

Table of Contents

Summary of Contents for DS 24D




































































































































Search results

Summary of Contents for DS 24D

Reviews:

Related manuals for DS 24D

Brands by name

Popular brands

Samsung DS 24D, User Instruction

Search results

Summary of Contents for DS 24D

Reviews:

Related manuals for DS 24D

Brands by name

Popular brands