Samsung CT26F7SWX/XAP Service Manual Download Page 12 | Manualshive

Page: 12 / 40

background image

Disassembly and reassembly

3-2

Samsung Electronics

3-2 Main Board Removal

3-3 Speaker Removal

1. Separate the socket board from the CRT neck.

2. Remove the Anode Cap from the CRT.

3. Remove the main board by pulling it with both hands.

Warning: The FBT is charged with high voltage.
Before removing the Anode Cap, discharge the voltage
through one of the heat sinks on the main board.

1. Remove the speaker by

pressing the tension rib.

«
...
10
11
12
13
14
...
»

Summary of Contents for CT26F7SWX/XAP









































Reviews:

No comments

Related manuals for CT26F7SWX/XAP

Brand: Yamaha Pages: 8

HTR-3064 Series

Brand: Yamaha Pages: 8

Aventage RX-A820

Brand: Yamaha Pages: 2

Aventage RX-A770

Brand: Yamaha Pages: 6

Aventage RX-A720

Brand: Yamaha Pages: 18

AVENTAGE RX-A1060

Brand: Yamaha Pages: 6

Aventage RX-A1020

Brand: Yamaha Pages: 8

SmoothFlite RRS

Brand: AR Pages: 67

Brand: ESX Pages: 40

Miami Beach CD148

Brand: Blaupunkt Pages: 17

Brand: Altronix Pages: 8

SRT 4356 PVR Evolution

Brand: Strong Pages: 74

In-Wall IR Receiver AIR6

Brand: ATON Pages: 2

Brand: Aerial-51 Pages: 3

Brand: Navico Pages: 87

Brand: Hemisphere GPS Pages: 43

Brand: Metronic Pages: 20

Brand: Intek Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands