background image

Disclaimer:  This information is provided “as is” without warranty of any kind

  

either expressed or implied, including, but not limited to, the implied

  

warranties of merchantability and fitness for a particular purpose.

REV 8-1

                

SERVICE BULLETIN

PRODUCT:  

Computer Monitor

BULLETIN:  

MON 97-007

MODEL:       

CMB5477L

SUBJECT:  

Flyback Transformer Revisions

BACKGROUND:  

Samsung instituted new revision flyback transformers as of

October 24, 1996.  The new flyback transformer will prevent intermittent no
raster conditions.  The revised flyback transformers that have been applied to
the latest production runs will have resistance values changed in the x-ray
protection and the high voltage adjustment circuits.

SOLUTION:  

When replacing a flyback transformer refer to the parts list below.

The resistance values should be changed accordingly.  If the resistance values
are different from the flyback transformers listed below, intermittent no raster or
shutdown conditions will exist.  Refer back to the original parts list and
schematic located in the service manual for any flyback transformer without a
revision number or label on it.

PARTS LIST:

ORIGINAL

NEW

Location No.

Part No.

Description

Part No.

Description

T402

BH26-10303V

REV.04 FSA15A003

SAMSUNG

BH26-10303V

REV.05 & REV.06

FSA-15A003

SAMSUNG

R516

2004-001319

1/4W, 86k ohm

2004-001349

1/4W, 91k ohm

R411

2001-000054

1/4W, 3.9k ohm

2004-000899

1/4W, 4.7k ohm

R412

2001-000722

1/4W, 4.3k ohm

2004-000698

1/4W, 3.3k ohm

Summary of Contents for CSR5987























Reviews: