Samsung CSR5987 Page 14 Service Bulletin Download | Manualshive

Page: 14 / 22

background image

Disclaimer: This information is provided “as is” without warranty of any kind

either expressed or implied, including, but not limited to, the implied
warranties of merchantability and fitness for a particular purpose.

REV8-1

SERVICE BULLETIN

PRODUCT:

Computer Monitor

BULLETIN:

MON 97-004

MODEL:

CFX1577L

SUBJECT:

Vertical Positioning Shifted Off Center

BACKGROUND:

Q302 and R327 fail in the vertical positioning circuit. The

failure is caused by a current surge during power up and from the monitor
recovering from an extended period in the DPMS Suspend mode.

SOLUTION:

Replace Q302, Q303, and R327 with different ratings. Production

went under these changes as of February 1, 1997. Observe the pin configuration
when replacing Q302.

PARTS LIST:

ORIGINAL

NEW

Location No.

Part No.

Description

Part No.

Description

Q302

0501-000586

KSC945, 150mA

0502-000006

KSC1507, 200mA

Q303

0501-000008

KSC733C, 150mA

0501-000294

KSA708, 700mA

R327

2001-000526

R-CARBON, 1/6 W

2003-000590

MO, 2W, 22 ohm

«
...
12
13
14
15
16
...
»

Summary of Contents for CSR5987























Reviews:

No comments

Related manuals for CSR5987

Brand: Samsung Pages: 13

Brand: A&D Pages: 5

Brand: Daktronics Pages: 29

Brand: Planar Pages: 24

Brand: b-red Pages: 8

Brand: smartheart Pages: 82

Brand: Uniden Pages: 32

Brand: TV One Pages: 12

UMEN-260314-V1.0

Brand: NewHawk Pages: 14

ErgoAct OEM Monitor

Brand: Intergraph Pages: 18

Brand: AOC Pages: 61

GOT3187W-881-PCT

Brand: AXIOMTEK Pages: 56

Brand: Pixio Pages: 12

Premium Digital 01-561

Brand: smartheart Pages: 68

Brand: Dahua Technology Pages: 12

Brand: J-Tech Digital Pages: 10

FP1921 rellhealthcare

Brand: Rell Healthcare Pages: 31

Brand: Uniden Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands