Samsung CL29K40MQ Service Manual Download Page 50

Page: 50 / 85

Disassembly & Reassembly

12-2

Samsung Electronics

Part Name

Description

Description Photo

Chassis

Holder

①

Separate the Ass'y Holder chassis from the Front Cabinet.

②

Pull the Chassis Holder lifting the fixing clip up.

: Pulling the Chassis Holder by force may damage the clip or

the connector. Pull the Chassis Holder just until the clip comes
off the hole.

Main Board

①

Separate the Speakers, the Speaker Wire, the D-Coil Master

Wire, and the Remote Control Sensor Cable from the Front
Cabinet and the System Board.

②

Separate the wire from the Wire pressing the at.

: Since there is a clip to connect the Connector Header in the

Wire Connector, pulling it by force may damage the clip or the
connector. Press the clip down completely and pull the
connector.

①

Separate theAV and Main Board from the Front Cabinet and

AV Wire, GT-Pin Wire.

②

To separate the Wire, Fixing clip and pressing the Wire.

①

Separate the 7P, 8P Wire connecting the DY Wire and the

CRT PCB.

②

To separate the Wire, Fixing clip and pressing the Wire.

Pull the chassis while raising the

clip fixing the Front Cabinet and

the Holder Chassis.

12-1-2 Disassembling the CRT and Chassis

Summary of Contents for CL29K40MQ






















































































Search results

Summary of Contents for CL29K40MQ

Reviews:

Related manuals for CL29K40MQ

Brands by name

Popular brands

Samsung CL29K40MQ, Service Manual

Search results

Summary of Contents for CL29K40MQ

Reviews:

Related manuals for CL29K40MQ

Brands by name

Popular brands