Samsung BN68-01699A-00 Page 37 User Manual Download

Page: 37 / 44

english -

Check Points before requesting Service

Symptom

Solution

does not

work.

■ Check if the device is an device. The system supports

devices only.

■ Connect only one receiver.

■ Check if the device power cord is properly connected.

■ Check the device’s Video/Audio/HDMI cable connections.

■ Check whether (HDMI-CEC) is set to On in the setup menu.

■ Check whether the TV remote control is in TV mode.

■ Check whether it is exclusive remote control.

■ doesn’t work at a certain condition. (Searching channels, Plug & Play,

etc.)

■ When connecting or removing the HDMI cable, please make sure to search

devices again or restart your TV.

■ Check if the Function of device is set on.

I want to start

■ Check if the device is properly connected to the TV and check if the

(HDMI-CEC) is set to On in the Setup menu.

■ Press the

button on the TV remote control to switch to TV. Then press the

toolS

button to show the menu and select a menu you want.

I want to exit .

■ Select

View tV

in menu.

■ Press the

SourCe

button on the TV remote control and select a device other

than devices.

■ Press any of

Pre-Ch

, and such to change to the

TV mode. (Note that the channel button operates only when a tuner-embedded

device is not connected.)

the Connecting to

device…

message appears on

the screen.

■ You cannot use the remote control when you are configuring or

switching to a view mode.

■ Use the remote control when the setting or switching to view mode is

complete.

the device

does not play.

You cannot use the play function when Plug & Play is in progress.

the connected device

is not displayed.

■ Check whether or not the device supports functions.

■ Check whether or not the HDMI cable is properly connected.

■ Check whether (HDMI-CEC) is set to On in the setup menu.

■ Search devices again.

■ You can connect an device using the HDMI cable only. Some HDMI

cables may not support functions.

■ If it is terminated by an abnormal situation such as disconnecting the HDMI cable

or power cord or a power failure, please repeat the device scan.

the tV programme

cannot be recorded.

Check whether the antenna jack on the recording device is properly connected.

BN68-01699A-00Eng-0603.indd 35

2008-06-03 �� 5:15:04

Summary of Contents for BN68-01699A-00













































Search results

Summary of Contents for BN68-01699A-00

Reviews:

Related manuals for BN68-01699A-00

Brands by name

Popular brands

Samsung BN68-01699A-00, User Manual

Search results

Summary of Contents for BN68-01699A-00

Reviews:

Related manuals for BN68-01699A-00

Brands by name

Popular brands