Samsung AM TN4 KH Series Installation Manual Download Page 36

Page: 36 / 40

Installation Procedure

English

Installation Pr

edur

Performing final check and trial operation

To complete the installation, perform the following checks and tests to ensure that the air conditioner operates
correctly.

Check the followings.
• Strength of the installation site
• Tightness of pipe connection to detect a gas leak
• Electric

wiring

connections

•  Heat-resistant insulation of the pipe
• Drainage
•  Earth conductor connection
•  Correct operation (follow the steps below)

After finishing the installation of the air conditioner, you should explain the following to the user. Refer to appropriate
pages in the User’s Manual.

How to start and stop the air conditioner

How to select the modes and functions

How to adjust the temperature and fan speed

How to adjust the airflow direction

How to set the timers

How to clean and replace the filters

NOTE

• When you complete the installation successfully, hand over the User’s Manual and this Installation Manual to the

user for storage in a handy and safe place.

Summary of Contents for AM TN4 KH Series









































Search results

Summary of Contents for AM TN4 KH Series

Reviews:

Related manuals for AM TN4 KH Series

Brands by name

Popular brands

Samsung AM TN4 KH Series, Installation Manual

Search results

Summary of Contents for AM TN4 KH Series

Reviews:

Related manuals for AM TN4 KH Series

Brands by name

Popular brands