background image

ENGLISH-7

01

 

Pr

EP

ar

at

ION

Choosing the installation location

Indoor unit

 

Install the unit at a place close to the wall facing the outside as it is necessary to perform piing connection with the 
outdoor unit .

 - It is effective to install the unit at the place where air flow is not blocked and the cool air can be distributed throughout 

the room . 

 

Install the unit at a place where there is no obstacle against the wind around the air intake and air outlet .

 

Avoid a place near the door which is frequently used by people .

 

Avoid a place exposed to direct sunlight . (If it is unavoidable, install a sunshade) .

 - Surface of the product may get discolored .

Install it on even ground .
•  Make sure there is no abnormal operation or noise generation .
•  If installed on uneven ground, water may overflow .

Outdoor unit

 

Avoid a place exposed to direct sunlight . (If it is unavoidable, install a sunshade) .

 

A place free from the risk of combustible gas leakage .

 

A place which can bear the weight of the unit .

 

A place which can bear the fixing strength of the outdoor unit .

 

Avoid a place exposed to oil (including machine oil)

 

Avoid a saline place .

 

Avoid a place exposed to sulfide gas (hot spring zone) . 

 - When installing the unit at such special environmental conditions, it may cause trouble to the product . When it is 

unavoidable, special maintenance is required .

 

A place where discharged air and noise of the outdoor unit does not disturb the neighborhood .

 - Take extra care not to cause any inconvenience to your neighbors when installing the unit on the borderline with your 

neighborhood .

 

A place where strong wind does not head against the air outlet of the outdoor unit .

 - If a strong wind heads directly against the air outlet at the time of cool operation, a safety device can be operated .

Do not install the outdoor unit on a unstable places (such as rooftop) . If installation is unavoidable, make sure that you 
fixed the unit firmly . Avoid places where strong wind or storm can possibly knock down the product (such as seashore or 
place with frequent storm)

FAC MEMORY-EU_IM_04036A-03_EN.indd   7

2016-03-30   오전 10:58:21

Summary of Contents for AF**FSSDA Series

























Reviews: