background image

5 Troubleshooting

5-1

5 Troubleshooting 

Notes:

1. Before troubleshooting, setup the PC’s display as below.

• Resolution: 1280 x 768
• H-frequency: 61 kHz
• V-frequency: 75 Hz

2. If no picture appears, make sure the power cord is correctly connected.

3. Check the following circuits.

• No raster appears: Function PBA,  Main PBA, I/D PBA
• 5V develop but no screen: Main PBA
• 5V does not develop: I/D PBA

4. If you push and hold the “    (Enter/Auto)” button for more than 5 seconds, the monitor 

automatically returns to the factory preset.

5-1-1 No Power 

When Pin 4 of CN600 is 0V 

does proper DC 13V, 5V 

appear at Pin 1, 2 and 6, 7 of 

CN600 separately?

Change IP Board.

Check Function Ass’y.

Yes

Yes

No

When Pin 3 of IC602 is DC 5V 

does proper DC 3.3V appear at 

Pin 4 of IC602?

Check IC602 and related

circuit.

Yes

No

When Pin 4 of IC600 is DC 0.3V 

does proper DC 3.3V appear at 

Pin 5 and  6 of IC600?

Check IC600 and related

circuit.

No

Yes

When Pin 2, 3 of IC601 is

DC 3.3V does proper DC 4.3V appear

at Pin 1 of IC601?

Check IC601 and related

circuit.

No

Yes

When Pin 2, 3 of IC601 is

DC 4.3V does proper DC 2.5V appear

at Pin 4 of IC601?

Check IC601 and related

circuit.

No

*

* 0V means power on state.

When the monitor work well except DPMS and power switch off, 
0V should be applied to number 4 of CN600.

Summary of Contents for 913V - SyncMaster - 19" LCD Monitor



































Reviews: