Samson Series 420 Manual Download Page 33

Page: 33 / 40

EB 7500 EN

Conversion

9.2 Operating mode change-

over in Type 3424-2 i/p

Converter

The i/p module is in the x input in x mode
and in the w

ext

input in w

ext

mode.

1. Release lock and completely pull out the

plug-in unit.

2. Pull the three-pin cable connector for the

mA signal off the converter board.

3. Unscrew the fastening screw (6) at the

controller module and pull the module off
together with the i/p converter from the
self-seal push-on fittings. Lift it out of the
control station.

4. Pull the three-pin cable connector for the

mA signal off the terminal plate.

5. Swap the location of the O-ring and

washer on the holes on the inside of the
plate as shown in Fig. 20.

x mode

6. Seal tight the w

ext

input of the compact

controller connecting plate (Fig. 16) with
a screw plug with

NPT thread.

The w

ext

port at the plug connection of

the control station must be sealed.

ext

mode

7. Open the w

ext

port at the plug connection

by unscrewing the M4 hexagon socket
screw at the w

ext

port and insert 4 x 2

O-ring included.
Seal tight the w

ext

input of the compact

controller connecting plate (Fig. 16) with
the

NPT screw.

8. Reinstall converter and plug on the cable

connector.

Fig. 20:

Operating mode changeover of i/p

converter

Self-seal push-on

fittings

Blanking

plug w

ext

Washer for x mode

O-ring for w

ext

mode

O-ring for w

ext

mode

Washer for x mode

Summary of Contents for Series 420









































Search results

Summary of Contents for Series 420

Reviews:

Related manuals for Series 420

Brands by name

Popular brands

Samson Series 420, Manual

Search results

Summary of Contents for Series 420

Reviews:

Related manuals for Series 420

Brands by name

Popular brands