Samson 3730-4 Page 83 Configuration Manual Download | Manualshive

Page: 83 / 100

background image

• FST_MEAS_DATA1…3_DEAD_TI_FALL
• FST_MEAS_DATA1…3_T63_FALLING
• FST_MEAS_DATA1…3_T98_FALLING
• FST_MEAS_DATA1…3_RISE_TI_FALLING
• FST_MEAS_DATA1…3_SETTL_TI_FALLING

FST_CANCEL_CONDITIONS (226)

Storage class: S · Read/write capability (r/w) · Supported modes: ALL

Cancelation conditions of the full stroke test (FST)
• FST_CANCEL_COND_MAX_TEST_DURA:

Maximum test duration (user-defined)

• FST_CANCEL_COND_ACTIV_MAX_TIME:

Activation 'Max. breakaway time'

• FST_CANCEL_COND_MAX_BREAK_TIME:

Maximum breakaway time

• FST_CANCEL_COND_ACTIV_TIME_REACH:

Activation 'Allowed time to reach full closed position'

• FST_CANCEL_COND_TIME_REACH:

Allowed time to reach full closed position

FST_DISPLAY (227)

Storage class: – · Read capability (r)

Information on the full stroke test (FST)
• PROGRESS_FLAG
• STATUS_FST
• NUMBER_OF_TESTS
• RECOMMEND_SCAN_RATE
• DURATION_OF_TEST
• TEST_INFO

FST_SETTTINGS (225)

Storage class: S · Read/write capability (r/w) · Supported modes: ALL

Settings for full stroke test (FST)
• FST_SETTINGS_TOL_LIMIT_RESPONSE (tolerance limit of step response)
• FST_SETTINGS_ACTIV_RAMP_FUNC (activation of ramp function)
• FST_SETTINGS_RAMP_TIME_RISING (ramp time rising)
• FST_SETTINGS_RAMP_TIME_FALLING (ramp time falling)
• FST_SETTINGS_SETTL_BEFORE_START (settling time before test starts)
• FST_SETTINGS_DELAY_AFTER_STEP (delay time after step)
• FST_SETTINGS_SCAN_RATE (scan rate)

KH 8384-4 EN

83

AO Transducer Block, Slot 1

· Manufacturer-specific parameters

«
...
81
82
83
84
85
...
»

Summary of Contents for 3730-4





































































































Reviews:

No comments

Related manuals for 3730-4

Daedal 412LXR Series

Brand: Parker Pages: 47

Brand: Samson Pages: 128

Brand: ABB Pages: 72

Brand: STI Pages: 17

Brand: STI Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands